Flight levels and altitude rules

1 contributors Last edited: Anonym Updated: 14. 6. 2026 Revision history

Flight levels and altitude rules

Vertical navigation uses two reference systems: altitude (above mean sea level, altimeter set to QNH) and flight level (Flight Level, altimeter set to the standard pressure of 1013.25 hPa). The switch between them happens at the transition altitude (TA) when climbing and at the transition level (TL) when descending. Thanks to this, all aircraft at higher levels share the same reference and separation is maintained.

How it works

Altitude (QNH) vs. flight level (STD 1013.25 hPa) Flight levels (FL) — altimeter set to STD 1013.25 hPa above the transition level (TL) Transition Level (TL) — above it, switch QNH → STD transition layer Transition Altitude (TA) — CZ 5,000 ft; below it, switch STD → QNH Altitude (AMSL) — altimeter set to QNH below the transition altitude GROUND

Below the TA you fly on QNH (the altimeter shows the actual altitude above sea level). When passing the TA you switch to STD (1013.25 hPa) and read flight levels. When descending you do the opposite at the TL. Between the TA and TL is the “transition layer", where you do not fly level.

ReferenceSettingUse
AGLabove the terraintraffic pattern, radar vectors
AMSL (QNH)pressure reduced to sea levelbelow the transition altitude
FL (STD)1013.25 hPaabove the transition level

Transition altitude: Czech Republic → Europe → World

RegionTransition altitude
Czech Republicfixed at 5,000 ft (throughout the Praha FIR)
Europenot harmonised and often low (in the order of 4,000–6,000 ft); it differs from country to country, in some places by airport. There is an effort to harmonise it (HETA).
World (USA)fixed at 18,000 ft for the whole country — much higher than in Europe.

That is why, on a flight in the USA in the simulator, you switch to STD much higher than in Europe — always check the TA for the area (from the chart/ATIS).

The semicircular rule

So that opposite-direction traffic is separated by altitude: for IFR by magnetic track, 0–179° odd FLs (FL350, FL370…), 180–359° even FLs (FL340, FL360…). VFR (where permitted) usually flies 500 ft higher. In RVSM airspace (FL290–FL410) levels are spaced every 1,000 ft, otherwise every 2,000 ft above FL290.

What a flight level (FL) is

A flight level (FL) is a height referenced to a uniform standard pressure of 1013.25 hPa, expressed in hundreds of feet. FL350 therefore means a pressure altitude of 35,000 ft with 1013 set. The trick is that all aircraft above the transition altitude use the same datum — even though the actual pressure changes with the weather, they remain correctly vertically separated from each other. If everyone flew on a different (local) pressure, the levels would drift apart and there would be a risk of collision. FL is therefore the basis of a safe vertical arrangement of traffic (see airspace).

Altimeter setting by altitude transition altitude BELOW it: altimeter on QNH → altitude above sea level (ft) (airport, approach, terrain) ABOVE it: altimeter on STD 1013 hPa → flight level (FL) (FL100, FL350… a common datum for everyone)
Above the transition altitude everyone flies on the same 1013 pressure — that is why the separation works.

QNH, QFE and the standard 1013

An altimeter is a barometer — what it shows depends on the reference pressure that is set. QNH sets the altimeter to show altitude above sea level (on the ground, the airport elevation) — it is used low down (approach, terrain). QFE shows height above the airport (zero on the ground) — today rather marginal. The standard pressure 1013 (QNE) is set above the transition altitude for flying at flight levels. Getting the setting wrong is a serious mistake — which is why the altimeter setting is called out and cross-checked on every climb and descent (see meteorology on pressure and QNH).

RVSM — reduced vertical separation

At high altitudes, a 2,000 ft separation used to be kept between levels, because altimeters are less accurate up there. Thanks to modern avionics, aviation introduced RVSM (Reduced Vertical Separation Minimum): between FL290 and FL410 a separation of only 1,000 ft is enough, giving twice as many usable levels and more room for traffic (and optimal levels for fuel). RVSM requires approved, accurate equipment and maintenance; it was introduced in Europe in 2002. For a sim pilot this means that above FL290 the levels are “packed" every 1,000 ft.

MEA, MSA and minimum levels

Altitude is limited not only by traffic but also by terrain and navigation reception. That is why there are minimum altitudes: MEA (Minimum En-route Altitude) — the lowest altitude on a route segment that guarantees safe terrain clearance and signal reception; MSA (Minimum Sector Altitude) — the lowest altitude around an airport (usually within 25 NM) with a safe margin over obstacles; and the lowest usable flight level, derived from the QNH. You will find these figures on charts, and they act as the “floor" below which you must not descend in a given area.

Choosing a cruise level in practice

The actual level is determined by several factors at once: the direction of flight (the semicircular rule, discussed above), the wind (use a tailwind, avoid a headwind — see jet stream), the aircraft's performance and weight (the optimum level rises as fuel is burnt — hence the step climb, climbing gradually during the flight), the terrain (MEA/MSA) and, of course, ATC instructions. The dispatcher (and tools such as SimBrief) look for the compromise that saves the most fuel and time. That is why a long flight is not flown at one level but climbs “in steps" towards the optimum.

Practical steps — X-Plane

Enter the target FL into the FMS/autopilot; when climbing through the TA, switch the altimeter to STD (in the Zibo 737 the STD button on the EFIS, in ToLiss the button on the FCU/“pull"; in the G1000 via the BARO knob to 29.92 inHg / 1013). When descending below the TL, go back to the QNH from the ATIS. Watch the units — hPa (Europe) vs. inHg (USA, 29.92).

Practical steps — DCS World

DCS lets you set the barometric altimeter; watch the units and reference: Western modules (F-16C, F/A-18C, A-10C) work with QNH in inHg / feet, many Soviet aircraft (MiGs, Sukhois, helicopters) traditionally with QFE in mmHg and metres. In joint missions, agree on a common reference (often QNH). Do not forget to set the altimeter according to the briefing, otherwise reported altitudes will be inconsistent.

Common mistakes

  • Forgetting to switch QNH/STD — a wrong altitude relative to others; the most common beginner mistake.
  • Mixing up units — 1013 hPa vs. 29.92 inHg; metres vs. feet (DCS).
  • Wrong FL parity — flying an even level in the wrong direction (semicircular rule).

FAQ

Why exactly 1013.25 hPa? It is the ISA standard pressure at sea level — a common “zero" for everyone, so aircraft stay correctly spaced on their levels regardless of the weather.

What is QFE? A pressure set so that the altimeter reads 0 on the ground (height above the runway threshold). It is used mainly in some military and Eastern operations.

When exactly should I switch? When climbing, at the moment you pass the TA; when descending, on reaching the TL (given by ATC or the chart).

Safety and limitations

  • Wrong QNH — an old/foreign setting can mean your actual altitude is hundreds of feet different; critical on approach (CFIT).
  • Cold air — at low temperatures the altimeter over-reads the actual altitude; a correction is applied in the mountains.
  • Always confirm the reference — if in doubt, check with ATC.

Related links


Sources (verified 06/2026): ICAO Doc 8168 (PANS-OPS) and Annex 2, SERA regulation, Czech AIP (ENR 1.7 altimetry); for the USA, FAA AIM. Sim-specific details per the documentation of Eagle Dynamics and the X-Plane module developers. An educational summary; for a real flight, use current official documents.