Contents
Czech Republic airspace
Czech airspace consists of the Praha FIR (ICAO code LKAA, from the ground to FL660; above FL195 as a UIR) and is managed by ŘLP ČR, s.p. (Air Navigation Services of the Czech Republic). The rules are based on the European SERA regulation and the national regulation L2 (Rules of the Air); oversight is carried out by the ÚCL (Civil Aviation Authority). Understanding its structure is the basis of a safe VFR and IFR flight.
Airspace classes in the Czech Republic
In practice, the Czech Republic uses classes C, D, E and G:
| Class | IFR | VFR | Service |
|---|---|---|---|
| C | ✅ | ✅ (clearance) | IFR/IFR and IFR/VFR separation |
| D | ✅ | ✅ (clearance) | IFR separation, VFR traffic information |
| E | ✅ | ✅ (no clearance) | controlled for IFR, information for VFR |
| G | ✅ | ✅ | uncontrolled (FIS) |
Vertical structure
- D — CTR of controlled aerodromes (from the ground to ~3,000 ft); entry requires a tower (TWR) clearance.
- C — TMA Praha (the only class C TMA in the Czech Republic, up to FL165) and the CTA above FL95 up to FL660.
- E — from 1,000 ft AGL to FL95 (controlled for IFR, VFR without clearance).
- G — below 1,000 ft AGL outside controlled airspace (uncontrolled).
CTR Praha (LKPR): class D, from the ground to 3,000 ft, radius approx. 9 NM; controlled by TWR. Above it lies TMA Praha (class C), controlled by APP (Praha Radar/Approach).
Special zones: ATZ, RMZ, TMZ
- ATZ (aerodrome traffic zone) — around an uncontrolled aerodrome, a circle with a radius of 3 NM (5.5 km) from the aerodrome reference point, up to 4,000 ft; pilots inform each other on the designated frequency.
- RMZ (Radio Mandatory Zone) — established two-way radio communication is mandatory for entry.
- TMZ (Transponder Mandatory Zone) — operation of a transponder is mandatory, usually mode C/S.
Flight information service (FIS)
Outside controlled airspace (and elsewhere too), information is provided by FIS — callsign Praha Information — throughout the Praha FIR. It gives traffic and weather information and the status of airspaces. It does not issue clearances, but it greatly increases safety; listening out is recommended.
Military and temporary areas
- TSA (temporary segregated area) and TRA (temporary reserved area; can be crossed after coordination with ATC) — for military activity.
- R / P / D — restricted / prohibited / danger area.
- CDR — conditional routes (dependent on the activation of military areas).
Sharing between civil and military traffic is decided by the AMC cell; you can find out the current status of areas from NOTAM and from FIS.
VFR meteorological minima (VMC, per SERA)
| Altitude | Visibility | Distance from cloud |
|---|---|---|
| ≥ FL100 (≥ 3,050 m) | 8 km | 1,500 m horizontally / 300 m (1,000 ft) vertically |
| below FL100, above 900 m AMSL / 300 m above terrain | 5 km | 1,500 m / 300 m (1,000 ft) |
| low (classes C–E) | 5 km | 1,500 m / 300 m (1,000 ft) |
| low (class G) | 5 km | clear of cloud and in sight of the surface |
Minimum flight heights (Czech Republic)
- Over congested areas and gatherings of people: at least 300 m (1,000 ft) above the highest obstacle.
- Elsewhere: at least 150 m (500 ft) above the ground or water.
The transition altitude in the Czech Republic is 5,000 ft (see Flight levels).
Where to find it
Boundaries, frequencies and entry points are in the VFR Manual (aim.rlp.cz) and the Czech AIP (especially ENR 2.1). Always check current restrictions in NOTAM before a flight.
Practical steps — X-Plane / VATSIM / DCS
- X-Plane/MSFS: you can display the airspaces in Little Navmap or on a CZ/SK VFR chart (Navigraph); before a VFR flight, check the CTR/TMA/ATZ along the route and the frequencies.
- VATSIM/IVAO: to enter controlled classes (C/D) you need a clearance from VACC Czech controllers; in uncontrolled airspace, listen to Praha Information.
- DCS: Czech civil airspace is not modelled (it is a combat sim); to practise real airspace use MSFS/X-Plane.
Common mistakes
- Entering a CTR/TMA without clearance — class D/C requires established contact and a clearance.
- Confusing AGL/AMSL at airspace boundaries — read the reference carefully.
- Ignoring RMZ/TMZ — you may not enter without radio contact/a transponder.
- Not checking TSA/TRA activation — a military area can “close" a route; read the NOTAM.
FAQ
Do I need a clearance to enter class E as VFR? No — VFR in E flies without clearance; only IFR traffic is controlled.
What is the difference between an ATZ and a CTR? An ATZ is at an uncontrolled aerodrome (mutual information); a CTR is a control zone (TWR clearance).
Where is class A or B in the Czech Republic? They are practically not used; the upper airspace is class C.
Do I have to call Praha Information? It is not mandatory outside an RMZ, but strongly recommended — it increases safety.
Safety and limitations
- VMC minima also apply in uncontrolled class G — maintain visibility and distance from cloud.
- A transponder is mandatory in a TMZ; in controlled airspace expect an assigned squawk.
- NOTAM and military area activation — always before a flight.
Exact definition of the classes in the Czech Republic
The Czech Republic uses four classes, and their extent is defined in the Czech AIP as follows:
| Class | Where in the Czech Republic |
|---|---|
| C | TMA Praha and all airspace above FL95 (up to FL660) |
| D | the CTR/MCTR and TMA/MTMA of all aerodromes except TMA Praha |
| E | outside CTR/TMA from 1,000 ft AGL to FL95 |
| G | outside CTR from the ground to 1,000 ft AGL |
In other words: the most controlled airspace is around Prague and the upper airspace (C); around the other aerodromes there are controlled CTR/TMA in class D; the “intermediate layer" up to FL95 is E (controlled for IFR); and near the ground outside control zones there is free class G. (The general theory of classes A–G can be found in the article Airspace.)
The Praha FIR and ATS units
The whole of Czech airspace forms a single flight information region, the Praha FIR (LKAA), managed by ŘLP ČR (Air Navigation Services of the Czech Republic). Traffic is handled by units according to the phase of flight:
- ACC Praha (area control centre) — controls en-route traffic at higher levels.
- APP (approach) — controls arrivals/departures in the TMA.
- TWR (tower) — controls traffic in the CTR and at the aerodrome.
- FIS (Praha/Brno Information) — information service for flights outside controlled airspace.
During the flight you are “handed off" between units to new frequencies — just as in other countries (see IFR).
Main controlled airspaces in the Czech Republic
The largest and most complex is the area around Prague (LKPR, Václav Havel Airport) — it has a CTR (class D) and an extensive TMA (class C), because it is the busiest Czech airspace (see LKPR). Other civil aerodromes also have control zones (CTR/TMA, class D), for example Brno (LKTB), Ostrava (LKMT), Karlovy Vary (LKKV) and Vodochody (LKVO). Smaller aerodromes operate as uncontrolled (see below). The exact boundaries, heights and frequencies of the individual airspaces are in the Czech AIP and on VFR charts — always according to the current status (as of 06/2026).
Military aerodromes and areas
The Czech Republic also has military aerodromes with their own control zones, MCTR/MTMA (class D), for example Čáslav (LKCV), Náměšť nad Oslavou (LKNA), Přerov (LKPO) and Praha-Kbely (LKKB). A civil pilot may not enter them without coordination. Military (and other special) use is served by temporary segregated/reserved areas, TSA/TRA, and training areas, which are activated only at certain times — when they are not active, they can usually be crossed (see activation below).
Flight information service (FIS) and frequencies
Outside controlled airspace (classes E and G) you are served by the flight information service — in the Czech Republic Praha Information and Brno Information (divided into sectors by area). It provides traffic and weather information, area activation and an alerting service, but it does not control (it does not issue clearances or provide separation). The specific frequencies of the individual FIS sectors and controlled units can be found in the Czech AIP (ENR 1.4 / 2) and in the VFR Manual — there is no point quoting them from memory because they change; always use a current source. Listening to FIS and making position reports is strongly recommended in uncontrolled airspace.
Reporting points and entering controlled airspace
VFR traffic around aerodromes uses reporting points — named places (often after villages or landmarks) through which you enter and leave the CTR/TMA. The pilot reports their position relative to a reporting point and requests a clearance to enter controlled airspace (CTR/TMA of class C/D). They may not enter without a clearance. Reporting points and VFR routes are drawn on VFR charts and in the manual; knowing them is the basis of safe VFR flying around controlled aerodromes (see VFR in the Czech Republic).
Activation of temporary areas
Temporary areas (TSA/TRA, training, parachuting, model flying) are not active all the time. Their planned activation is published in advance (the airspace use plan), and the current status is announced by NOTAM (see NOTAM) and via FIS. Before a flight, the pilot checks which areas will be active along their route and either flies around them or requests a crossing. Flying into an active prohibited/restricted/military area is a serious infringement (and a safety risk) — which is why checking activation is a mandatory part of preparation.
Aerodromes without a tower: AFIS and RADIO
Most Czech aerodromes are uncontrolled. Instead of a tower (TWR), there is either AFIS (Aerodrome Flight Information Service — it does not control, it only informs) or a RADIO station (providing basic information), or simply two-way radio communication on the aerodrome frequency. At an uncontrolled aerodrome, pilots separate themselves by reporting their position in the circuit and by lookout. This regime is common at flying-club and smaller aerodromes in the Czech Republic — which is why it is important to be able to fly a circuit and communicate even without a “controller" (see Radiotelephony).
Transition altitude and pressure setting
In the Czech Republic the transition altitude is 5,000 ft. Up to it, the aircraft indicates altitude using the local pressure QNH; above the transition level it switches to the standard 1013 hPa and flies at flight levels (FL). Thanks to this, all aircraft at higher levels share “the same zero" and guaranteed separation (see Flight levels). VFR cruising levels in the Czech Republic follow the semicircular rule according to the direction of flight (with an extra 500 ft for VFR) — for details see VFR in the Czech Republic.
Drones in the Czech Republic
The operation of unmanned aircraft systems (drones) in the Czech Republic follows the uniform EU rules (Open/Specific/Certified categories) and is overseen by the ÚCL. Operators register, pilots take an online test and restrictions apply (typically max 120 m AGL, visual line of sight, no flying over prohibited areas or near aerodromes without coordination). There are also apps and maps for flying drones in the Czech Republic showing where flying is allowed. This too is part of “airspace" — drones and aircraft share the sky and must stay clear of each other (see Air law).
Gliding and sport flying
The Czech Republic has a strong tradition of gliding and sport aviation. Gliders mainly use classes E and G and thermals; special areas are established for gliding, parachuting, aerotows and other activities, which are activated as needed (and announced via NOTAM/FIS). Around flying-club aerodromes you must therefore expect climbing gliders, aerotow combinations and parachute drops. This variety of traffic is why uncontrolled airspace places an emphasis on lookout and position reports — you will meet powered aircraft, gliders, ultralights and balloons there.
Online: Czech Division (VATSIM / IVAO)
The great news for sim pilots is that the Praha FIR is actively staffed on the online networks VATSIM and IVAO (the Czech divisions). When a controller is online, you can fly Czech airspace with real phraseology, clearances and procedures — from taxiing at LKPR to an en-route flight and approach. The Czech divisions also organise events (fly-ins) and training. It is the best way to try out how Czech airspace works in practice without any risk (see VATSIM, IVAO). Phraseology and procedures follow the Czech AIP.
Charts and sources for the Czech Republic
The authoritative source is the Czech AIP and the VFR Manual (aim.rlp.cz, ŘLP) — they contain the exact boundaries, heights, frequencies and reporting points of all airspaces. For planning there are VFR charts (ICAO 1:500,000) and online tools (e.g. AisView for current area activation and NOTAM). Always use the current edition in the valid AIRAC cycle — airspaces, frequencies and procedures change. In the sim (X-Plane/MSFS), Czech airspace is usually in the nav data, but for a realistic VFR flight it pays to have a real VFR chart or the manual at hand (see Aeronautical charts).
Flights near the border and neighbouring states
The Praha FIR borders the airspace of Germany, Poland, Slovakia and Austria. When flying towards the border, ŘLP will hand you off to the neighbouring unit (and vice versa). Thanks to SERA, the rules are uniform throughout the EU, so the VMC minima and the logic of the classes stay the same — only the specific layout of the airspaces and the frequencies differ. A cross-border VFR flight is therefore smooth; you just need to know the reporting points and frequencies on both sides and have current charts of both countries.
Related links
- Airspace classes A–G (ICAO classification + world) · VFR flights in the Czech Republic
- Flight levels · LKPR · NOTAM
- Glossary — CTR, TMA, FIR, ATZ, RMZ, TMZ, FIS, TSA/TRA, SERA
Sources (verified 06/2026): Czech AIP and VFR Manual (ŘLP ČR), regulation L2, the SERA regulation (VMC minima Table S5-1), ÚCL. For flight planning, always use the current official documents (AIP, NOTAM).