Wake turbulence — vortices behind aircraft

2 contributors Last edited: Anonym Updated: 14. 6. 2026 Revision history

Wake turbulence — vortices behind aircraft

Wake turbulence consists of powerful air vortices left behind by every aircraft that generates lift. They are invisible, can persist for minutes and pose a serious danger to a smaller aircraft behind a large one — from an uncontrolled roll to structural damage. That is why there is separation according to weight categories.

📷 Image placeholder: wake vortices made visible by smoke or in cloud behind a wing
We will add a real photo (vortices in cloud/smoke).

How the vortices form

At the wingtip, the higher pressure from below “spills over" to the lower pressure on top and spins up a wingtip vortex. Two counter-rotating vortices form, one behind each wingtip. They are a by-product of lift — related to induced drag; the greater the lift, the stronger the vortices.

When the vortices are strongest: “Heavy, Clean, Slow"

They are most dangerous behind an aircraft that is heavy, in a clean configuration (no flaps) and flying slowly (a high angle of attack = maximum lift per unit of speed). Typically, then, a large aircraft on approach or just after takeoff.

Weight categories

ICAO (classic, 3+1 categories):

CategoryMTOWExample
SUPER (J)A380 (and An-225)A380
HEAVY (H)> 136,000 kgB747, B777, A330
MEDIUM (M)7,000–136,000 kgA320, B737
LIGHT (L)< 7,000 kgC172, PA-28

RECAT-EU (EUROCONTROL) refines the system into 6 categories A–F (by wingspan and MTOW), and in pair-wise (PWS) mode determines separation precisely between specific pairs of types — which for some combinations allows smaller separations and higher airport throughput while maintaining safety.

Separation (ICAO, radar on approach — example)

Leader / followerHEAVYMEDIUMLIGHT
behind SUPER6 NM7 NM8 NM
behind HEAVY4 NM5 NM6 NM
behind MEDIUM——5 NM

For departures, time-based separations (2–3 min) are also used. RECAT-EU adjusts the values for specific pairs.

Vortex behaviour

Wake turbulence: the vortices sink and drift heavy aircraft counter-rotating vortices sink ~300–500 fpm me: stay ABOVE and upwind Near the ground the vortices spread sideways (~2–3 kt) and are carried by the wind.
  • Sinking: at altitude the vortices sink at ~300–500 ft/min and level off roughly 500–900 ft below the generating aircraft's flight path.
  • Near the ground: at heights below ~100–200 ft the vortices spread sideways (~2–3 kt); the wind carries them (beware of calm conditions and a light crosswind, which holds a vortex over the runway).
  • Ground effect stops them sinking — the vortices linger and move sideways.
  • Decay takes time: in calm weather they persist longer.

Where the danger lies

  • Approach and takeoff — low, slow, close behind a heavy aircraft (the most common case).
  • Crossing the track below a heavy aircraft (the vortices sink into your level).
  • The same runway after a heavy aircraft's departure/landing in a light wind.

How to avoid them

  • With a persistent vortex: climb slightly and move upwind.
  • Landing behind a heavy: fly above its glide path and touch down beyond its touchdown point.
  • Taking off behind a heavy: lift off before its rotation point and climb above its flight path.
  • Respect the separation and the ATC warning “caution wake turbulence".

Lessons from an accident — American Airlines 587 (2001)

An A300 shortly after takeoff (~1,700 ft) behind a Boeing 747 encountered wake turbulence. The first officer responded with aggressive and repeated rudder inputs — the aerodynamic load tore off the vertical stabiliser. The lesson: the vortex itself does not usually destroy an aircraft; excessive/cyclic control inputs (especially rudder) do. Respond smoothly, do not exceed the control limits.

Separation in practice — time and distance

So that a weaker aircraft does not fly into the vortices of a stronger one, ATC maintains separation according to category. On a radar approach it is measured by distance (NM), and behind departures from the same runway by time (usually 2 minutes, or 3 minutes from an intermediate part of the runway). Indicative values according to the classic ICAO classification:

Leader (heavier)Follower (lighter)Min. separation on approach
Super (A380)Heavyapprox. 6 NM
Super (A380)Mediumapprox. 7 NM
Super (A380)Lightapprox. 8 NM
HeavyMediumapprox. 5 NM
HeavyLightapprox. 6 NM
MediumLightapprox. 5 NM

Between aircraft of the same category, or when a lighter aircraft leads a heavier one, no special separation is required. The values are indicative — the exact figures are set by the regulations of the given state/airport.

The A380 and the Super category

The largest airliner, the Airbus A380, generates such strong vortices that a separate “Super" category was created for it, with larger separations than for ordinary Heavies. After incidents in which the A380's wake upset aircraft flying several miles behind it (and thousands of feet lower on crossing tracks), the separations were refined. It is a clear illustration of the rule “the heavier the leader, the greater the spacing behind" — and of why categories are introduced according to the real strength of the vortices, not “by eye".

RECAT — finer categories

The classic three to four categories (Light/Medium/Heavy/Super) are coarse. That is why RECAT (Re-categorisation) is being introduced — in Europe, RECAT-EU divides aircraft into six groups more precisely by weight and wingspan. The aim is to safely reduce unnecessarily large separations where the vortices are not so strong, and thereby increase the throughput of busy airports (more takeoffs and landings per hour) without any loss of safety. It is a good example of how a better understanding of vortex physics turns into a practical increase in capacity.

Vortices near the ground and wind

Vortices low over the runway during takeoff and landing are especially insidious. Normally they sink and decay, but a light crosswind can hold them right over the runway (one vortex is blown away, the other stays) — endangering the next aircraft. That is why separations near the ground are strict and, when landing behind a heavy aircraft, the crew chooses a touchdown beyond its touchdown point, and when taking off, a lift-off before its rotation point, to avoid the vortices. Watch out for helicopters too — a hovering helicopter creates a strong downwash that is dangerous for small aircraft nearby.

Practical steps — simulators

Both MSFS and X-Plane model wake turbulence — try an approach close behind an AI “heavy" and you will feel the roll. On VATSIM/IVAO, ATC applies separation by category. In DCS you feel the wake during refuelling/formation flying (behind a large tanker).

Common mistakes

  • Flying under the track of a heavy aircraft — the vortices sink into your level.
  • Touching down before a heavy's touchdown point (into its vortices).
  • Excessive control inputs in a vortex (AA587).
  • Relying on dispersal in calm conditions — a vortex lingers over the runway longest then.

FAQ

Why “Heavy, Clean, Slow"? That is when the wing produces the most lift per unit of speed → the strongest vortices.

How long do the vortices last? Tens of seconds to minutes; longer in calm weather.

Where does a vortex sink to? ~500–900 ft below the generating aircraft; that is why you fly above its path.

What should I do when hit by a vortex? Smoothly level the wings, do NOT over-control (especially with the rudder).

Safety and limitations

  • Separations are a minimum — in calm conditions be cautious beyond them.
  • Smooth control inputs in turbulence; respect the structural limits (rudder).
  • “Caution wake turbulence" — take it seriously, especially behind a super/heavy.

Related links


Sources (verified 06/2026): FAA AIM (section 7-4 Wake Turbulence), EUROCONTROL RECAT-EU, ICAO Doc 4444 (separation), NTSB AAR-04/04 (American Airlines 587), Wikipedia/SKYbrary. Values verified from multiple sources.