Contents
Airspace — classes A to G
The sky is not one big open space — it is divided into classes A to G according to how dense the traffic is and what service and protection aircraft receive in them. The classification was introduced by ICAO (Annex 11), and in Europe it is harmonised by the SERA rules. The class determines who may fly there (IFR/VFR), whether an ATC clearance is needed, what separation is provided and which weather minima apply. Understanding the classes is fundamental — without it you cannot legally and safely plan a flight, whether real or in the sim on the VATSIM/IVAO networks.
Controlled vs. uncontrolled airspace
The basic division is into controlled and uncontrolled airspace:
- Controlled (classes A–E) — there is air traffic control (ATC), which issues clearances and provides separation (at least for part of the traffic). This includes the airspace around airports and the main routes.
- Uncontrolled (classes F–G) — ATC does not provide separation here; pilots separate themselves on the “see and avoid" principle and receive only a flight information service (FIS).
The denser the traffic (large airports, high levels), the “stricter" the class — conversely, over fields at low altitude there is usually free class G. An airport is typically surrounded by a “wedding cake" of controlled airspace (a CTR at ground level, a TMA above and around it).
Class by class
- Class A — IFR only (VFR prohibited). Everyone is separated, a clearance is required. Typically upper airspace and the main routes.
- Class B — IFR and VFR, everyone is separated from each other; a clearance is required. (Practically unused in Europe; in the USA it covers the largest airports.)
- Class C — IFR and VFR, a clearance is required. IFR is separated from IFR and VFR; VFR is separated from IFR and receives traffic information on other VFR traffic (and avoidance advice on request). Typically the TMAs of large airports.
- Class D — IFR and VFR, a clearance is required. IFR is separated from IFR; between IFR and VFR and between VFR flights, traffic information is given (not separation). Typically the CTRs around towers.
- Class E — IFR and VFR. IFR is separated from IFR and controlled; VFR does not need a clearance and is not separated (it gets information where possible). Supplementary controlled airspace.
- Class F — IFR receives only an advisory service (where established), VFR an information service; a transitional/disappearing category.
- Class G — uncontrolled; IFR and VFR without separation, FIS only. Free airspace (in our country usually low above the terrain outside controlled areas).
Summary table of services
| Class | Flights | Clearance | ATC separation |
|---|---|---|---|
| A | IFR only | yes | everyone |
| B | IFR+VFR | yes | everyone from each other |
| C | IFR+VFR | yes | IFR from all; VFR from IFR |
| D | IFR+VFR | yes | IFR from IFR only |
| E | IFR+VFR | IFR only | IFR from IFR only |
| F | IFR+VFR | no | no (advisory only) |
| G | IFR+VFR | no | no (FIS only) |
VMC minima — visibility and distance from cloud
For a pilot to fly VFR (see and avoid), VMC (Visual Meteorological Conditions) must be met. The minima per SERA (table S5-1):
| Altitude / class | Visibility | Distance from cloud |
|---|---|---|
| at/above FL100 (all) | 8 km | 1,500 m horizontally / 1,000 ft vertically |
| below FL100, above 3,000 ft | 5 km | 1,500 m / 1,000 ft |
| ≤ 3,000 ft, classes A*–E | 5 km | 1,500 m / 1,000 ft |
| ≤ 3,000 ft, classes F, G | 5 km | clear of cloud and in sight of the surface |
(*VFR is not permitted in class A.) At very low altitude and low speed (≤ 140 kt IAS), the visibility in G can be reduced to 1,500 m, and even lower for helicopters. The logic is clear: the higher and denser the traffic, the stricter the minima; A/B only have a visibility limit, because there ATC separates everyone.
Special VFR (SVFR)
When the weather in a control zone (CTR) is below VMC but the pilot wants to fly visually, they can request Special VFR — a clearance to fly VFR in controlled airspace even in poorer visibility, if traffic permits. ATC then “threads" the SVFR aircraft through so that it does not obstruct IFR traffic. It is an exception for low altitudes around airports, not a normal mode.
Transponders, RMZ and TMZ
Besides the classes there are supplementary zones and equipment requirements:
- TMZ (Transponder Mandatory Zone) — airspace where a transponder is mandatory, even though it is otherwise uncontrolled.
- RMZ (Radio Mandatory Zone) — airspace with mandatory radio contact (position reports/listening watch).
- Mode S / ADS-B: in Europe and the USA the requirement for modern transponders is growing; in the USA ADS-B Out is required in most controlled airspace and above 10,000 ft.
These requirements increase traffic awareness even where ATC does not provide separation.
Speed and altitude restrictions
In much airspace there is a speed limit of 250 kt IAS below FL100 (below 10,000 ft), so that pilots and ATC have time to react in denser, lower traffic. Associated with the airspace are also the cruising level rules (see Flight levels) and the transition altitude/level for the pressure setting.
How classes map onto real airspace
The class is the “rule"; the specific airspace structures are its “container":
- CTR (Control Zone) — a controlled zone from the ground around an airport (often class D).
- TMA (Terminal Manoeuvring Area) — a terminal control area above/around an airport (often class C).
- CTA / airway — a control area / airway (classes A–E).
- FIR (Flight Information Region) — a large region in which a flight information service is provided.
You will find the same abbreviations and colours on aeronautical charts; reading them is a basic skill.
Transition altitude and pressure setting
Airspace is also related to how altitude is measured. Up to the so-called transition altitude, the aircraft reports its altitude above sea level according to the local pressure QNH (e.g. “3,500 ft"); above the transition level it switches to the standard pressure of 1013 hPa and flies at flight levels (FL, e.g. FL120). In the Czech Republic the transition altitude is 5,000 ft. The point is that all aircraft at higher levels measure altitude “from the same zero" and are guaranteed to pass with the correct separation — this is closely related to the division and use of airspace (in detail see Flight levels).
Czech Republic → Europe → World
In the Czech Republic (data in the Czech AIP, as of 06/2026), classes C, D, E and G are used: a TMA is usually class C, a CTR class D, above the lower routes class E (up to about FL95) and uncontrolled G near the ground (in detail see Czech airspace). In Europe the rules are harmonised by SERA, so the VMC minima and the logic of the classes are the same across states (the specific airspace layout differs). Worldwide, the same ICAO system applies, but with local deviations — the US system is markedly different: classes A, B, C, D, E and G (no F), an “upside-down wedding cake" of class B around the large airports and the so-called Mode C veil. The rule: always study the chart and AIP of the destination country.
In practice — X-Plane / MSFS
- Before the flight, find the airspace classes along the route and around the airports (CTR/TMA) on the chart and plan where you need a clearance.
- On the VATSIM/IVAO networks, practise requesting entry into class C/D (clearance, position reports); it is the best training for real-world practice.
- Plan VFR flights according to the VMC minima (visibility, distance from cloud) and avoid inadvertently infringing controlled airspace.
- Try a Special VFR entry into a CTR in deteriorating weather.
In practice — DCS World
DCS is military and does not model the formal civil classes A–G. You will, however, meet related concepts: prohibited/restricted/danger areas (restricted/MOA), the airfield control zone and the carrier control zone (CCZ). In multiplayer with ATC (ATC scripts), a looser equivalent of takeoff/approach clearances applies. The principle of “where may I fly and what do I need" is the same, just without the civil classification — to practise airspace classes, use a civil sim.
Why the sky is divided at all
The division into classes is a compromise between safety and freedom. Where many fast aircraft meet (large airports, high-level routes), a firm hand from ATC, clearances and separation are needed — hence the strict classes A–C. Where a few small aircraft fly low over the countryside, the same strictness would only cause unnecessary delays, so there is free class G, where pilots manage with lookout and radio. The classification thus “tailors protection" to the density and risk of the traffic: maximum freedom where possible, maximum control where necessary.
How to request entry into controlled airspace
Entering class C/D (e.g. a CTR/TMA) requires a clearance. In practice this means calling the relevant unit in good time and asking. The call has a set structure: who you are calling, who you are, where you are, at what altitude and what you want (e.g. “Praha Radar, OK-ABC, Cessna 172, 5 NM south of the beacon, 2,500 ft, request entry into the TMA"). ATC responds with a clearance (with conditions — heading, altitude, transponder code) or a refusal. You must not enter the airspace without a clearance. For phrases and procedure see Radiotelephony; on the VATSIM/IVAO networks it is everyday practice.
Other zones: ATZ, P/R/D, TSA/TRA
Besides classes A–G, special zones appear in the airspace:
- ATZ (Aerodrome Traffic Zone) — a zone around a smaller (uncontrolled) airfield with mandatory radio; in the Czech Republic typically up to 4,000 ft and a radius of 3 NM.
- Prohibited (P), restricted (R) and danger (D) areas — where flying is not allowed (P), allowed only under conditions (R), or where there is activity dangerous to aircraft (D, e.g. firing ranges).
- TSA / TRA — temporarily segregated/reserved areas (often for the military); when they are not active, they can be flown through.
These zones are published in the AIP and activated via NOTAM — always check them before a flight.
Flight information and advisory services
Even if ATC is not separating you, you are not alone. FIS (Flight Information Service) provides information about traffic, weather and the status of airspace; at airfields without a tower there is AFIS (an information service, not control — it does not issue clearances, it only informs). In some countries you can also get a radar information/advisory service. These services increase awareness and safety, especially in classes E–G, where separation is not provided.
Common mistakes
- Entering a CTR/TMA without a clearance — a classic airspace infringement; request the clearance in good time.
- Confusing the classes — flying VFR in class C without a clearance (in C a clearance is required, unlike in E).
- Underestimating the VMC minima — trying to “push on" into deteriorating weather.
- Ignoring active R/D areas or TMZs/RMZs — check the NOTAMs and the chart.
Safety and limitations
- Airspace infringement is a common and serious offence — an inadvertent entry into controlled airspace without a clearance; prevent it by planning and monitoring your position.
- Know the class and its rules before you enter the airspace (clearance? minima? transponder?).
- VMC minima are not recommendations — flying into cloud under VFR is dangerous and illegal.
- A transponder/radio is mandatory in a TMZ/RMZ; without them you may not enter the zone.
- In uncontrolled airspace, rely on lookout and listening — ATC is not separating you.
FAQ
What is the main difference between controlled and uncontrolled? In controlled airspace (A–E), ATC issues clearances and provides separation (for part of the traffic); in uncontrolled (F–G) it does not — you separate yourself.
Where is VFR not allowed? In class A (IFR only).
Do I need a clearance in class E as VFR? No — VFR in E does not need a clearance and is not separated; IFR in E does.
What are the VMC minima above FL100? 8 km visibility, 1,500 m horizontally and 1,000 ft vertically from cloud.
What are an RMZ and a TMZ? Zones with mandatory radio (RMZ) or a mandatory transponder (TMZ).
What is Special VFR? A clearance to fly VFR in a control zone even in poorer weather, if traffic permits.
What is an ATZ? A zone around a smaller (uncontrolled) airfield with mandatory radio (in the Czech Republic typically 3 NM / 4,000 ft).
What does transition altitude mean? The boundary above which you switch from QNH to the standard pressure of 1013 hPa and fly at flight levels (5,000 ft in the Czech Republic).
Which classes are used in the Czech Republic? C (TMA), D (CTR), E (up to ~FL95) and G (uncontrolled).
Related links
- Czech airspace · VFR in the Czech Republic · IFR flying · Flight levels
- Aeronautical charts · Radiotelephony · TCAS · Glossary — CTR, TMA, FIR, VMC, IMC, SVFR, RMZ, TMZ, FIS
Sources (verified 06/2026): ICAO Annex 11 (Air Traffic Services), SERA (Standardised European Rules of the Air, EASA — airspace classes and VMC table S5-1), FAA AIM chapter 3 (Controlled Airspace), Czech AIP (classes and airspace in the Czech Republic as of 06/2026); the services/separation of classes A–G, VMC minima (8 km/5 km, 1,500 m/1,000 ft), SVFR, RMZ/TMZ and US differences verified from multiple sources. For the specific airspace layout, see the current AIP/charts.