Contents
TAF — aerodrome forecast
A TAF (Terminal Aerodrome Forecast) is a weather forecast for an airport, usually covering 24–30 hours. Its format resembles a METAR, but it contains forecast change groups. Together with the METAR, it is the basis of planning.
Example
TAF LKPR 151100Z 1512/1612 25010KT 9999 FEW040 TEMPO 1512/1518 4000 TSRA BKN020CB BECMG 1518/1520 18005KT
Key groups
- BECMG — a gradual, lasting change within the given window.
- TEMPO — temporary fluctuations (less than half the period).
- FM (from) — a sudden complete change from the given time.
- PROB30/PROB40 — a 30/40% probability of the phenomenon.
What a TAF is and who issues it
A TAF (Terminal Aerodrome Forecast) is a weather forecast for an airport — unlike the METAR, which describes the current state, a TAF tells you what weather is expected. It applies to the vicinity of the airport (roughly within 5 NM / 8 km of the reference point) and is issued by the aerodrome meteorological office (in the Czech Republic, ČHMÚ). The format uses the same coding language as the METAR, so if you can read a METAR you can handle a TAF too — there are just additional time and change groups.
Validity and issue
TAFs are issued routinely, typically every 6 hours. The validity period is either short (9–24 h) or long (24–30 h) at major airports. In the code, the validity is written as the day/hour of the start and end — e.g. 1212/1312 means “from the 12th at 12:00 UTC to the 13th at 12:00 UTC". It is immediately followed by the base (prevailing) forecast and then any change groups, which describe how the weather will change during the validity period.
Breaking down a real example
Let's take: TAF LKPR 121100Z 1212/1312 24010KT 9999 SCT035 BECMG 1216/1218 28015G25KT TEMPO 1218/1222 SHRA BKN030CB. Breaking it down:
| Group | Meaning |
|---|---|
LKPR 121100Z | Prague airport, issued on the 12th at 11:00 UTC |
1212/1312 | valid from the 12th at 12:00 to the 13th at 12:00 UTC |
24010KT 9999 SCT035 | base: wind 240°/10 kt, visibility 10 km+, scattered cloud at 3,500 ft |
BECMG 1216/1218 28015G25KT | between 16 and 18 h the wind gradually veers to 280°/15, gusting 25 kt |
TEMPO 1218/1222 SHRA BKN030CB | between 18 and 22 h temporarily showers and a broken CB layer at 3,000 ft |
So you read the forecast as a “story of the weather" over time, not as a single state.
Change groups FM, BECMG, TEMPO, PROB
The key to a TAF is the change groups: FM (from) — a rapid and lasting change from the given time, replacing the previous state; BECMG (becoming) — a gradual change during the stated interval, which then persists; TEMPO — temporary fluctuations (each lasting less than an hour, in total up to half the period); and PROB30 / PROB40 — a 30% or 40% probability of the phenomenon (often PROB30 TEMPO). A higher probability is no longer written as PROB (it becomes the main forecast), and below 30% it is not given.
Which elements a TAF contains
A TAF forecasts wind, visibility, weather and cloud — with the same syntax as a METAR (see there for the details of the codes). It does not contain the dew point or pressure (QNH), however, because it is a forecast, not a measurement. Sometimes extreme temperatures are added (TX maximum, TN minimum, with times) or information on significant phenomena. The main thing is that the TAF shows you the trend: whether the weather will improve or deteriorate during your flight, whether the wind will change, or whether thunderstorms will come.
TAF and METAR together
In practice, the METAR and TAF are read together. The METAR gives the precise current state, the TAF the outlook for hours ahead. The pilot compares whether the forecast matches reality and uses the TAF to estimate what weather they will encounter on arrival (ETA). If the destination TAF forecasts a deterioration below minima at the time of arrival, that is a warning. The METAR+TAF pair is therefore the basis of every pre-flight decision.
Flight planning and alternate airports
The TAF is key for planning. It is used to decide whether the destination will be above landing minima at the time of arrival, and whether an alternate airport is needed — one is required when the destination forecast is not certain enough or forecasts worse conditions. The choice of alternate and the amount of fuel (see fuel planning) depend directly on the TAF. A misread TAF can mean arriving at a closed airport with no reserve — which is why it gets a lot of attention.
Why read it in the simulator
A TAF makes sense in the sim too: with live weather you can use it to plan whether to choose a different runway, allow for a thunderstorm or keep an alternate. On VATSIM/IVAO the TAF is a real basis for decisions. Practising reading TAFs (together with METARs and SimBrief) makes you a more considered pilot who does not fly “blind" but according to the forecast — exactly as in real operations.
TEMPO vs. BECMG — what to watch out for
Beginners often confuse BECMG and TEMPO. The difference is fundamental: BECMG describes a lasting change — the new state sets in during the interval and then stays (e.g. the wind changes direction and stays that way). TEMPO describes temporary fluctuations that come and go (e.g. brief showers), between which the base forecast applies. For safety, TEMPO and PROB groups must also be taken seriously — the fact that a phenomenon is only “temporary" or “30%" does not mean it can be ignored. On the contrary: if a TEMPO or PROB30 forecasts a thunderstorm or a drop below minima at the time of your arrival, you must allow for it in planning (alternate, fuel). A good rule: plan for the worst condition the forecast allows for at that time.
Practical steps
Before a flight, read the TAF for both the destination and the alternate. If the TAF forecasts conditions below minima (TEMPO/PROB), have a backup plan and fuel. In MSFS/X-Plane with live weather, watch how it develops; in DCS, set up a matching scenario in the editor.
Common mistakes
- Overlooking TEMPO/PROB — a temporary deterioration can drop below minima.
- Ignoring the validity — a TAF has a time window (from/to); outside it, it does not apply.
FAQ
How long is a TAF valid? Usually 24 or 30 hours (depending on the airport).
TEMPO vs. BECMG? TEMPO = temporary fluctuations; BECMG = a lasting change of state.
Safety and limitations
- A forecast, not a certainty — combine it with the current METAR and SIGMETs.
- Alternate airport — choose it based on its TAF, not just the destination's.
Related links
- METAR · Meteorology for pilots · Fuel planning
- Glossary — TAF, BECMG, TEMPO, PROB, FM
Sources (verified 06/2026): ICAO Annex 3 and Doc 8896, aviationweather.gov; ČHMÚ (aeronautical meteorological service). An educational summary; for a real flight, use current official documents.