Starting a turboprop engine

1 contributors Last edited: Anonym Updated: 14. 6. 2026 Revision history

Starting a turboprop engine

A turboprop engine combines a gas turbine with a propeller through a reduction gearbox. Most of the energy of the hot gases is transferred to the shaft (the propeller), and only a small part leaves through the exhaust. It is most efficient at low and medium altitudes and speeds (up to ~350 KTAS) — which is why it powers regional aircraft and GA types such as the King Air, TBM, PC-12 and Caravan. The start sequence is more complex than for a piston engine and requires careful temperature monitoring.

📷 Image placeholder: turboprop control quadrant (power/prop/condition lever) or the Ng/Np/ITT gauges
We will add a real photo / cockpit screenshot.

How a turboprop works

Free-turbine turboprop engine GAS GENERATOR (Ng) compressor combustion chamber GG turbine ~45,000 rpm POWER TURBINE (Np) free turbine ~30,000 rpm gearbox→ propeller ~2,000 rpm The free turbine is not mechanically connected to the generator → the propeller can be feathered while running. (The PT6 is “reverse-flow” — air enters at the rear, the exhaust is at the front.)

In the most widespread family, the Pratt & Whitney PT6 (and similar free-turbine engines), the engine has two separate parts:

  • Gas generator — a centrifugal compressor + combustion chamber + a turbine that drives the compressor. It spins very fast (in the order of ~45,000 rpm); its speed is given as Ng (or N1), usually in %.
  • Power (free) turbine — a separate turbine spun by the hot gases (~30,000 rpm), not mechanically connected to the generator; it drives the propeller through a reduction gearbox (~1,900–2,200 rpm). Its speed = Np.

The advantage of the free turbine: the propeller can be slowed or even feathered while running without shutting down the engine, and a possible “prop strike” does not damage the generator. For a given power lever position, the pilot can change the torque by setting the propeller RPM.

Two architectures

TypeDescriptionExample
Free turbinepower turbine separate from the generator; smoother, easier start, feathering while runningPT6 (King Air, TBM, PC-12, Caravan)
Single-shaft (fixed)propeller connected directly to the generator shaft; different handling and startHoneywell/Garrett TPE331

The gauges you watch

  • Ng / N1 — gas generator speed (%).
  • Np — propeller speed (rpm).
  • ITT (Interstage Turbine Temperature) — the most important during start; the temperature between turbine stages.
  • Torque — the power delivered to the propeller.
  • Fuel flow, oil pressure/temperature.

The control quadrant

LeverWhat it controls
Power levergas generator power (Ng), and in the ground range also the blade angle
Propeller leverpropeller speed (Np) via the governor
Condition leverfuel / mode: CUT-OFF → LOW IDLE → HIGH IDLE, or FEATHER

Beta, reverse and feathering

  • Beta range — the ground range in which the power lever directly sets the blade angle (fine control when taxiing).
  • Reverse — a negative blade angle for braking after touchdown.
  • Feather — blades turned edge-on (minimum drag) when an engine fails or is shut down.

Start sequence (step by step)

  1. Pre-start: battery/external power ON, fuel pump ON, ignition to AUTO/ON, visual check of the intake and exhaust, oil pressure.
  2. Motoring (dry crank): the starter spins the generator without fuel — this ventilates the engine; watch Ng rise and the oil pressure.
  3. Ignition: at the correct Ng the igniters are switched on.
  4. Fuel: condition lever from CUT-OFF to IDLE (on the PT6 through FEATHER to RUN) → fuel into the combustion chamber.
  5. Light-off: the engine lights — ITT rises sharply; watch the limit immediately!
  6. Stabilisation: the engine accelerates to idle; the starter disengages (typically around ~50% Ng); ITT drops to a stable value.
  7. Generator ON after stabilisation; post-start checks (oil, ITT, Ng at idle, propeller governor).

Dangers during start

ProblemCauseResponse
Hot starttoo much fuel / low RPM / late ignition — ITT exceeds the limitcondition lever CUT-OFF, motor for ~30 s, new attempt
Hung startthe engine lights but does not accelerate to idle (weak battery/starter)abort the start, find the cause
No light-offthe engine does not light (ignition/fuel failure)CUT-OFF, motor (to clear the fuel!), check
Compressor stallflow separation in the compressorabort, inspection/maintenance

The ITT limit during start is higher than the operating limit, but only for a few seconds — the exact value is in the engine manual. The worst mistake is leaving the ignition off and switching it on late — the accumulated unburnt fuel causes a certain hot start. If ITT jumps, cut the fuel immediately and motor the engine.

Cold weather

In freezing temperatures the oil is thick — motor longer and watch the oil pressure; some engines have a minimum oil temperature limit for starting. Preheating helps.

Practical steps — simulators

  • MSFS: King Air 350i, TBM 930/960, Kodiak 100, Cessna Caravan — all have a realistic “cold & dark” start (PT6). Turn off auto-start and work through the sequence manually.
  • X-Plane: B200 King Air, PC-12, TBM, MU-2 — excellent study turboprops.
  • DCS: there are practically no turboprops — DCS is mainly jet fighters and helicopters (note: the L-39 Albatros is a jet, with the AI-25TL engine, not a turboprop). Practise turboprop starts in MSFS/X-Plane.

Common mistakes

  • Not watching ITT at light-off — the most common route to a hot start.
  • Late ignition / fuel introduced before Ng is high enough.
  • Forgetting to motor after an unsuccessful start (unburnt fuel).
  • Mixing up the levers — condition vs prop vs power lever.

FAQ

Why a “free” turbine? The power turbine is not connected to the generator — smoother operation, the propeller can be feathered while running, and the generator is protected in a prop strike.

What is the most important thing to watch during start? ITT — exceeding the limit (hot start) damages the turbine.

Why a turboprop and not a jet for regional aircraft? A propeller is more economical at lower speeds/altitudes (efficient up to ~350 KTAS).

What does the beta range do? It is the ground range for fine taxiing control and reverse (direct control of the blade angle).

Safety and limitations

  • The ITT start limit is a hard limit — if exceeded, abort and record it (possible turbine damage).
  • Feathering after an engine failure reduces drag and improves controllability.
  • Follow the checklist for the specific type — the sequence differs from engine to engine.

Related links


Sources (verified 06/2026): Wikipedia (Pratt & Whitney PT6, Turboprop, Free-turbine), Covington Aircraft (torque/RPM), aircraftsystemstech (turbine start); the PT6 architecture, Ng/Np/ITT and hot/hung starts verified. Exact limits per the manual of the specific engine.