Jet engines — principle and types

2 contributors Last edited: Anonym Updated: 14. 6. 2026 Revision history

Jet engines — principle and types

A jet engine works on the principle of the Brayton cycle: intake → compression → combustion → expansion → exhaust. According to Newton's third law, the accelerated outflow of gases produces thrust.

📷 Image placeholder: a jet engine (turbofan) / the EICAS engine display
We will add a real photo / screenshot.

Types

TypeDescriptionUse
Turbojetpure jet without bypass, noisyolder / military
Low-bypass turbofanlow bypass (BPR ~0.5–2), often with an afterburnerfighters
High-bypass turbofanhigh bypass (BPR ~5–12), quiet and efficientairliners
Turbopropthe turbine drives a propellerregional / GA, efficient up to ~350 KTAS
Turboshaftthe turbine drives a shafthelicopters

Performance indicators

N1/N2 (fan/core speed), EGT/ITT (temperatures), EPR (pressure ratio). Modern control is handled by FADEC (fully digital), which protects the limits and optimises performance.

Modern trends

The geared turbofan (GTF), open-rotor concepts and SAF (sustainable aviation fuel, currently a blend of up to 50%) reduce consumption and emissions.

Jet engine — airflow intake compression combustion turbine airexhaust = THRUST “Suck – squeeze – bang – blow": a continuous process forces gases backwards → thrust forwards (Newton's 3rd law).
The Brayton cycle: air is drawn in, compressed by the compressor, mixed with fuel and burnt; the hot gases spin the turbine (which drives the compressor) and flow out to the rear — that produces thrust.

How a jet engine works (the Brayton cycle)

A jet engine works on a continuous Brayton cycle, colloquially “suck – squeeze – bang – blow": 1) the intake takes in air, 2) the compressor compresses it, 3) in the combustion chamber it is mixed with fuel and ignited (the temperature rises sharply), 4) the hot gases spin the turbine (which drives the compressor via a shaft) and flow out at high speed. Unlike a piston engine, which performs these phases alternately in one cylinder, a jet engine does them all at once and continuously — which is why it is so powerful and smooth.

Thrust and Newton's law

Thrust arises according to Newton's 3rd law (action–reaction): the engine accelerates a large mass of air backwards, and an equal force pushes the aircraft forwards. Thrust can therefore be increased in two ways — expel the air faster, or expel more air. Modern engines rely on the second approach (lots of air at a moderate speed), which is more efficient and quieter.

Bypass ratio

A key concept is the bypass ratio — how much air bypasses the engine core (through the large fan) compared with what passes through combustion:

  • Turbojet (no bypass) — all the air goes through the core; fast, but noisy and thirsty (older/military).
  • Low-bypass turbofan — a small bypass, often with an afterburner; fighters.
  • High-bypass turbofan — most of the thrust comes from the large fan (bypass ratios of up to 10–12:1); efficient and quiet — the standard for airliners.

That is why modern airliners have such huge nacelles — they contain a large fan that “pushes" a lot of air efficiently.

Turboprop and turboshaft engines

The same core (a gas turbine) can drive something other than a jet: a turboprop engine drives a propeller (efficient up to ~M0.5–0.6, regional aircraft, see starting a turboprop engine), and a turboshaft drives a shaft (a helicopter rotor, generators). The principle is the same; the only difference is where the turbine's power goes.

FADEC — digital engine control

Modern engines are controlled by a FADEC computer (Full Authority Digital Engine Control). The pilot just moves the thrust lever, and the FADEC meters the fuel itself, monitors the limits (temperatures, speeds), optimises performance and protects the engine against overload or surge. This simplifies operation and increases reliability — the pilot does not worry about the details, just “asks for thrust".

Construction: spools, sections and indicators

An engine typically has several spools: N1 (low pressure — the fan), N2 (high pressure — the core), and on large engines also N3. Power is monitored via the N1 speed (CFM/GE) or the EPR pressure ratio (Rolls-Royce, older P&W), together with the EGT exhaust gas temperature and fuel flow. These indicators tell you how hard the engine is “working" and whether it is within limits.

Thrust reversers

After landing, thrust reversers help with braking — doors redirect part of the exhaust/bypass air forwards, so the engine brakes. They are not the main brake (that is the wheels and spoilers), but they considerably shorten the landing roll, especially on a wet or icy runway. Reversers are used only on the ground and up to a certain speed.

Starting and engine malfunctions

Starting follows a sequence: the starter spins up the core, at sufficient speed fuel and ignition are added, the engine “lights" and accelerates to idle by itself. The pilot watches the EGT and speeds, because malfunctions are possible:

  • Hot start — the temperature during start shoots above the limit (risk of damage).
  • Hung start — the engine “hangs" at low speed and does not accelerate.
  • Compressor stall / surge — a breakdown of airflow in the compressor (a bang, loss of thrust).
  • Flameout — the flame goes out (e.g. after ingesting water/ice or a bird, see bird strike).
  • FOD — damage from a foreign object ingested into the engine.

History and future

Jet propulsion was invented independently by Frank Whittle (Britain) and Hans von Ohain (Germany) in the 1930s; the first jet flight was made by the Heinkel He 178 in 1939 (see History of aviation). Since then, engines have become enormously more powerful and efficient — from noisy turbojets to quiet high-bypass turbofans. The future is heading towards even more efficient concepts (e.g. geared turbofans / GTF), sustainable aviation fuels (SAF) and, in perspective, hybrid and electric propulsion for smaller aircraft. The aim is lower consumption, noise and emissions (related to fuel and the ecology of aviation).

Practical steps — X-Plane / DCS

In airliners, during engine start watch N2 → fuel → light-off (EGT) → idle; watch out for hot/hung starts. In DCS with fighters, deal with thrust management, the afterburner (fuel consumption!) and the risk of compressor surge in violent manoeuvres.

Common mistakes

  • Hot start — too much fuel / too little speed; watch the EGT/ITT limit and abort in time.
  • Overusing the afterburner — it quickly exhausts the fuel.

FAQ

Why is high-bypass quieter? A large part of the thrust comes from the slower bypass air — less noise, higher efficiency.

What is a flameout? The engine going out (e.g. water ingestion/icing); it is dealt with by a restart according to the procedure.

Safety and limitations

  • Temperature limits (EGT/ITT) — exceeding them damages the turbine.
  • Compressor surge — flow separation; it shows up as a bang and a drop in thrust.

Related links


Sources (verified 06/2026): propulsion textbooks (EASA ATPL), engine manufacturer documentation (CFM, P&W, RR). An educational summary; for a real flight, use current official documents.