Contents
Airport infrastructure
An airport is a system of movement areas, navigation and lighting aids and ground services. The standards are set by ICAO Annex 14.
Movement areas
- Runway (RWY) — takeoff/landing; the number = magnetic heading/10 (RWY 24 ≈ 240°).
- Taxiway (TWY) — designated by letters (A, B, C…).
- Apron — parking, loading, handling.
Navigation and lighting aids
- ILS (localizer + glideslope + markers).
- PAPI/VASI — visual glide path angle (PAPI: 2 red + 2 white = correct).
- ALS — approach lights; runway lights (edge, centreline, threshold, TDZ).
Ground handling
- Pushback tug, GPU, ASU (air start unit).
- Refuelling (bowser / hydrant), de-icing (Type I/IV).
- Catering, baggage, cargo.
What makes up an airport
An airport is divided into two main parts. The airside is the secured area beyond security screening — the runways, taxiways, aprons and everything only aircraft and authorised personnel can reach. The landside is publicly accessible — terminal halls, car parks, access roads. Between them are security screening and passport control. This division is the basis of every airport's layout and is related to aviation security (see air law).
The runway: designation and markings
A runway's number corresponds to its magnetic heading divided by ten, rounded — a runway with a heading of 093° is “09", and the opposite direction of the same runway is “27" (they differ by 180°, i.e. by 18). Parallel runways have the letters L/C/R (left/centre/right). On the runway there are white markings: the threshold “piano keys", the runway number, the centreline, the touchdown zone and the aiming point. Sometimes the threshold is displaced — landing starts only beyond it (e.g. because of an obstacle). The dimensions, surface and markings of runways are defined by ICAO (Annex 14).
Taxiways and holding points
Taxiways (TWY) connect the runways with the stands. They have a yellow centreline and are designated by letters (A, B, C…). Key are the holding points (hold-short) before the runway — yellow transverse lines that must not be crossed without a clearance (to prevent runway incursions). Orientation is aided by signs and boards: red “mandatory" signs (e.g. before a runway), yellow-and-black location and direction signs. Taxiing correctly according to the markings and ATC instructions is an essential safety element (see marshalling).
The apron and stands
The apron/ramp is where aircraft park, passengers board, refuelling and loading take place. The aircraft stands on a marked stand/gate; at the terminal a jet bridge leads to it, while on remote stands passengers board by stairs and bus. The aircraft is guided onto the stand by a marshaller or a visual docking guidance system (VDGS). The apron is busy (tugs, fuel trucks, catering) and strict movement rules apply.
The lighting system
For the airport to work at night and in reduced visibility, it has extensive lighting:
- Approach lights (ALS) — a row of lights before the threshold, guiding onto the centreline on approach.
- PAPI/VASI — the glide path indicator (“two white, two red = on profile").
- REIL — flashes identifying the runway ends/threshold.
- Runway lights — edge (white, changing to yellow/red towards the end), centreline, threshold (green) and end (red).
- Taxiway lights — blue edge, green centreline.
- Aerodrome beacon — alternating white/green at a land airport.
The pilot reads the colour “language" of the lights at night too (see Night VFR).
RVR and meteorology at the airport
For operations in fog, the runway visual range (RVR) is measured — sensors along the runway (at the start, middle and end) determine how far you can see at runway level. RVR is decisive for whether an approach of a given category can be flown (see ILS). The airport also has other meteorological sensors (wind, QNH pressure, temperature, cloud base), whose data go into the ATIS and METAR (see METAR). Without accurate weather measurement, approaches in low visibility could not be operated safely.
The control tower and traffic monitoring
Traffic at the airport and around it is controlled by the control tower (TWR) — it has a view of the runways and surfaces and issues clearances for takeoff, landing and taxiing. Large airports also have surface movement radar (ASDE) for monitoring movement on the ground in fog, and separate positions for ground (taxiing) and approach (arrivals/departures). A new development is remote towers, where the controller watches the airport via cameras from afar (see NextGen/SESAR).
Rescue and firefighting service (RFF)
Every public airport must have a rescue and firefighting service (RFF/ARFF) ready to respond to an accident on the airfield. ICAO divides airports into categories according to the size of the aircraft they can receive — a higher category means more fire vehicles, foam and personnel on standby. If the RFF category drops (equipment failure), it can restrict operations of large aircraft. It is an invisible but mandatory part of every airport's safety.
Heliports and small airfields
Not every airport is a large international hub. Small airfields (flying clubs) often have only a grass runway, simple markings and, instead of a tower, an information service (AFIS) or just radio. Heliports are areas for helicopters with a touchdown and lift-off area (TLOF/FATO) and their own markings (the letter H); you will find them on hospitals, buildings and in the field. Infrastructure thus scales from a few hundred metres of grass to a complex with several runways — the principle (a safe surface, markings, guidance) remains.
Safety on the airfield: FOD and runway incursions
The airfield has its own specific risks. FOD (Foreign Object Debris — bolts, fragments, ice) can damage tyres or be ingested into an engine, which is why the surfaces are regularly inspected and cleaned. The second risk is a runway incursion — an aircraft/vehicle entering an active runway without authorisation. It is prevented by clear markings and holding points, surface radar, lights and disciplined taxiing according to instructions. Both risks show that even “just" taxiing on the ground requires attention and order.
In simulators
Practise correct taxiing according to the markings and ATC (taxi via …) and parking at the gate. In DCS, deal with operations at air bases and on the aircraft carrier (catapults, arresting wires, deck crew).
FAQ
What is the TDZ? The touchdown zone of the runway (lights/markings).
What is the PAPI for? A visual check of the descent, even without an ILS.
Related links
Sources (verified 06/2026): ICAO Annex 14 (aerodromes), AIP; marking and lighting standards. An educational summary; figures are as of 06/2026.