Contents
ILS — the precision approach system
ILS (Instrument Landing System) is the most widespread ground-based guidance system, giving an aircraft both lateral and vertical guidance right down to the runway threshold. It was developed in the 1930s and 1940s and is still the backbone of low-visibility approaches at thousands of airports around the world — from small regional fields to LKPR. Thanks to two intersecting radio beams, it can bring an aircraft down safely even in fog, when the pilot cannot see the runway until almost the last moment. It is a precision approach: it provides guidance in both axes, unlike non-precision approaches (e.g. VOR/NDB), which only provide direction.
How ILS works
An ILS consists of two independent transmitters whose beams intersect on the ideal approach path:
- Localizer (LOC) — provides lateral guidance (left/right of the runway centreline). The antenna stands beyond the far end of the runway and transmits two overlapping lobes modulated with tones of 90 Hz (left) and 150 Hz (right). Where the signal is balanced lies exactly the runway centreline. The instrument (CDI/HSI) shows which way the aircraft has deviated.
- Glideslope / Glide Path (GS) — provides vertical guidance (above/below the glide path). The antenna stands beside the runway near the touchdown zone. Using the same two-tone principle it defines the descent plane, typically 3°.
The pilot (or the autopilot in APP mode) flies the aircraft so that both needles/deviation bars are centred — then the aircraft is exactly on the centreline and on the glide path. This is called “flying the cross”.
Components and sensitivity
Besides the two main beams, an ILS also includes aids for distance:
- Marker beacons — transmit vertically upwards on 75 MHz and announce passage over a specific point. The outer marker (OM) about 7 km from the threshold (400 Hz tone, dashes, blue light), the middle marker (MM) about 1 km out (1300 Hz, dot-dash, amber), and possibly an inner marker (IM) for CAT II/III. Today markers are often replaced by DME (distance measuring), which gives a continuous readout.
- Sensitivity — the localizer is much more sensitive than a VOR: full-scale needle deflection corresponds to ±2.5° (a course width of ~5°), and on the glideslope full deflection is only ±0.7° around 3°. That is why an ILS requires fine corrections — closer to the runway, every deviation grows in angular terms.
- Critical and sensitive areas — a taxiing aircraft or vehicle near the antennas can “bend” the beam. That is why low visibility procedures (LVP) are declared in poor visibility and these areas are protected (see NOTAM).
Frequencies and pairing
The localizer operates in the 108.10–111.95 MHz band (odd tenths) and the glideslope in UHF at 329.15–335.0 MHz. The pilot, however, tunes only one frequency — the VHF localizer — and the receiver automatically pairs the corresponding UHF glideslope. The ILS is identified by a Morse code (e.g. “ILKR”). The localizer shares its band with VORs; you can recognise ILS frequencies by the odd tenths in the lower part of the band.
ILS categories (accuracy and minima)
ILS approaches are divided into categories according to how low the aircraft may descend before it must have the runway in sight. Key terms: DH (Decision Height — the height at which the “land / go-around” decision is made) and RVR (Runway Visual Range). Values per ICAO Annex 10 / EASA:
| Category | Decision height (DH) | RVR (runway visual range) |
|---|---|---|
| CAT I | ≥ 60 m (200 ft) | ≥ 550 m (or visibility ≥ 800 m) |
| CAT II | 30–60 m (100–200 ft) | ≥ 300 m |
| CAT IIIA | < 30 m (100 ft) or none | ≥ 175 m |
| CAT IIIB | < 15 m (50 ft) or none | 50–175 m |
| CAT IIIC | none | no limit (not used operationally) |
The lower categories (CAT II/III) require more precise ground equipment, a certified autopilot and autoland, a trained crew and approval of both the operator and the airport. CAT III in practice means an automatic landing — the aircraft touches down by itself while the crew monitors. CAT I can be flown even by a single pilot with ordinary equipment.
Czech Republic → Europe → World
In the Czech Republic air navigation services are provided by ŘLP ČR; the highest category is at Prague/Ruzyně (LKPR) — runway 06/24 is equipped up to CAT III, allowing landings even in thick fog (verified from the Czech AIP). Procedures and minima are in the Czech AIP and on the approach charts (see Aeronautical charts). In Europe ILS is operated according to EASA/ICAO standards and SERA; large airports (Frankfurt, Amsterdam, Paris) have CAT II/III. Around the world ILS is universal — it is gradually being complemented by satellite approaches (RNP APCH/LPV, GBAS/GLS — see RNAV/RNP), but ILS remains key for the lowest minima and as a backup.
How to fly an ILS — the procedure
- Preparation: tune the ILS frequency, set the course to the runway heading, check the identification and the approach chart (minima, MAP, frequencies).
- Intercepting the localizer: you usually arrive in level flight, perpendicular or at an angle to the centreline; as soon as the localizer needle starts moving towards the centre, you turn onto the runway course and hold the centreline.
- Intercepting the glideslope: the glide path is intercepted from below (from level flight beneath it); as the glideslope needle comes down to the centre, you begin a ~3° descent and set the landing configuration (flaps, gear).
- Stabilised approach: hold the centreline and glide path, the target speed and vertical speed (about 700 ft/min at 3°), with small corrections.
- Decision at DH: at the decision height you must have visual references of the runway. If you do → land; if not → go-around (see Missed approach).
In practice — X-Plane / MSFS
- Tune the ILS frequency into NAV1 and set the course (OBS/CRS) to the runway heading from the chart.
- Arrive below the glideslope, in level flight, intercept the localizer first, then press APP (Approach) on the autopilot — the autopilot captures LOC and GS and flies the cross.
- In aircraft such as the Cessna 172 (G1000) watch the deviations on the PFD; in airliners (Zibo 737, FlyByWire A32NX) use APP mode and watch the FMA annunciations (LOC/GS captured).
- Also practise a hand-flown ILS without the autopilot — it teaches you fine corrections and the instrument “scan”.
In practice — DCS World
Military aircraft also use ILS at airfields in DCS:
- F/A-18C Hornet — ILS is selected on the UFC (you enter the airfield's ILS frequency); the localizer and glideslope deviations are shown on the HUD and HSI. You fly the cross just as with a civil ILS.
- A-10C II — has an ILS receiver; deviations on the HSI/ADI.
- You will find airfield ILS frequencies in the kneeboard / on the F10 map.
- NOTE — an aircraft carrier uses a different system: carrier landings use ICLS (channel-based, not ILS frequencies) and ACLS, plus optical guidance (the IFLOLS “lens”). Do not confuse them with a ground ILS (see Types of approach).
Safety and limitations
- False glideslope: the glideslope also radiates false lobes higher up (e.g. around 6°/9°); that is why the glide path is intercepted from below and a reasonable height/distance is cross-checked (against DME or height above the threshold).
- Beam bending: a taxiing aircraft/vehicle in the critical area can make the LOC/GS oscillate — under LVP these areas are protected; do not ignore suspicious deviations.
- Stabilisation: an ILS tempts crews to “press on” with an unstable approach; the stabilised approach rule applies — if the parameters are not right by the specified height, go around.
- CFIT and minima: descending below DH without visual references is one of the causes of CFIT accidents; DH/RVR are hard limits, not recommendations (see Aviation accidents).
- Interference: mobile phones and unsuitable transmitters can interfere with the ILS — hence the restrictions in the cabin.
FAQ
What does an ILS give you that a VOR approach doesn't? Vertical guidance (the glideslope) — an ILS is a precision approach, a VOR only a non-precision one (direction only).
Why intercept the glideslope from below? To avoid capturing a false upper lobe, which would lead to a steep descent.
What does CAT III mean? The lowest minima — in practice an automatic landing (autoland) with certified equipment, crew and airport.
Do I have to tune the glideslope separately? No — you tune only the VHF localizer; the UHF glideslope is paired automatically.
Will satellite approaches replace ILS? They are gradually complementing it (LPV, GBAS/GLS), but ILS remains for the lowest minima and as a backup.
Antennas and integrity monitoring
Neither the localizer nor the glideslope radiates just “one beam” — they are formed by arrays of antennas whose combination produces a precise radiation pattern with two overlapping lobes. Accuracy is vital, so every ILS has monitoring: an independent sensor (near-field and far-field monitors) checks that the beam lies within the specified tolerance. As soon as the signal deviates (a fault, bending, a shift), the system automatically shuts down or raises a warning flag, so that aircraft do not receive incorrect guidance. The pilot must therefore take an ILS flag/warning seriously — better a go-around than flying on a faulty signal. This “better nothing than wrong” philosophy is the foundation of precision approach safety.
Low visibility procedures (LVP)
For CAT II/III approaches an airport declares LVP — Low Visibility Procedures. Their purpose is to protect the accuracy of the ILS and ensure safe movement in fog:
- Protection of critical areas — taxiing aircraft and vehicles must keep away from the antennas so as not to bend the beam; taxiing is restricted.
- RVR measurement — the runway visual range is measured at several points (touchdown zone, midpoint, end of the runway) and reported to the crew.
- Reduced capacity — traffic slows down and separation increases, because everything takes longer.
- Backup power and increased monitoring of the systems.
LVP are the reason why only a few (suitably equipped) aircraft fly in thick fog and traffic is delayed — safety takes precedence over capacity (see NOTAM, where LVP and ILS status are announced).
Coupled approach and autoland in depth
An ILS is “readable” by the autopilot, which is why it is flown as a coupled approach — the autopilot follows the LOC and glideslope by itself (APP mode, see Autopilot). In an autoland (CAT II/III) the aircraft goes all the way to touchdown: at low height it reads the radio altimeter, performs the flare, aligns the nose from any crosswind crab angle (de-crab) and after touchdown holds the runway centreline (rollout). So that a single failure does not interrupt the approach, several autopilots run simultaneously (Airbus annunciates this as LAND 2 / LAND 3). The crew actively monitors throughout and is ready to take over control or go around at any moment.
Stabilised approach
Even with a perfect ILS, the principle of the stabilised approach applies: by a certain height (typically 1,000 ft in IMC, 500 ft in VMC above the terrain) the aircraft must be “in its target state” — on the centreline and glide path, at the target speed, in the correct configuration (flaps, gear), with a reasonable rate of descent. If any parameter is off, the right thing is to discontinue and go around (see go-around). Trying to “rescue” an unstable approach is a classic cause of landing accidents — the ILS provides guidance, but the discipline must come from the crew.
Alternatives and successors: MLS, GBAS/GLS, LPV
ILS has served for decades, and successors have been sought:
- MLS (Microwave Landing System) — was supposed to replace ILS (curved approaches, resistance to reflections), but with the arrival of satellite navigation it never caught on apart from a few airports.
- GBAS / GLS — a ground station augments GPS and transmits a GLS approach; one station can serve several runways and curved paths. So far mainly CAT I, with development towards lower minima — the real modern successor to ILS (see GPS).
- LPV (via SBAS/EGNOS) — a precision-like approach with vertical guidance without a ground beacon, close to ILS CAT I (see RNAV/RNP).
Even so, ILS remains: for the lowest minima (CAT III) it is still the standard, and as a ground-based system it is independent of GPS, so it also serves as a backup when satellites are jammed.
History of ILS
The principles of ILS were developed in the 1930s; the first ILS approaches and landings took place in the USA at the end of the 1930s, and after the Second World War ILS became an ICAO standard. Categories II and III and automatic landing were added over time, so aircraft can now land even in conditions where the pilot can practically not see the runway. After decades of development ILS is one of the longest-serving and most trusted aviation systems — and even in the era of satellite navigation it holds its place for the most demanding approaches.
Related links
- Types of approach · VOR navigation · RNAV/RNP and LPV · Go-around
- Autopilot · Aeronautical charts · LKPR Prague · Glossary — DH, RVR, LOC, GS, LVP, autoland, CFIT
Sources (verified 06/2026): ICAO Annex 10 (Aeronautical Telecommunications), FAA AIM 1-1-9 and Order 6750.16E, EASA/SKYbrary (Precision Approach), IVAO documentation; categories I–III (DH/RVR), the LOC band 108.10–111.95 MHz and GS 329.15–335.0 MHz, full-scale deflections ±2.5°/±0.7°, 75 MHz markers and LKPR CAT III (Czech AIP) verified from multiple sources.