Contents
Go-Around — missed approach
A go-around (missed approach) is the discontinuation of an approach and a renewed climb. It is a standard, safe manoeuvre — not a failure. Every pilot must be able to perform it without hesitation.
When to go around
- At the DA/DH or MDA without visual contact with the runway.
- An unstabilised approach below 1,000/500 ft AGL.
- The runway is occupied (aircraft, vehicle, wildlife).
- A windshear warning, an ATC instruction, or simply “something isn't right".
Procedure
- TOGA — full/takeoff thrust.
- Climb attitude (~15°), follow the flight director.
- Positive rate → gear up.
- Gradually retract the flaps according to the schedule.
- Follow the published missed approach procedure (MAP) — headings, altitudes.
A go-around is not a mistake
It is essential to understand that a go-around (missed approach) is a normal, safe procedure, not a pilot failure. On the contrary — a timely decision to discontinue a landing is a sign of good judgement. The aircraft goes from the approach back into a climb and either tries again or flies to the alternate. There are many reasons: an unstable approach, traffic or an obstacle on the runway, bad weather at minima, an ATC instruction, a technical problem. The mindset “better to try again than to push an unstable approach" saves lives.
Procedure step by step
A go-around has a practised sequence (details depend on the type):
- Thrust: set takeoff/go-around thrust (TOGA) — full or a defined power.
- Attitude: raise the nose to the climb attitude (according to the command bars / ~15°).
- Flaps: retract one step to the takeoff/approach position (reduces drag — not all at once).
- Climb and gear: with a positive rate of climb (“positive climb"), retract the gear.
- Acceleration and clean-up: accelerate, reach a safe speed, clean up the flaps.
- Track and altitude: fly the published missed approach track to the given altitude.
The crew divides the tasks (PF flies, PM sets and calls out) — which is why the briefing before the approach is important, so that the go-around happens “automatically".
Balked landing — rejecting after touchdown
A special case is the balked (rejected) landing — a go-around initiated very low, in the flare or even after the wheels touch (e.g. when an obstacle appears or the landing does not work out). It is more demanding: the aircraft is slow, with full flaps and close to the ground. The procedure is similar (thrust, attitude, clean-up), but with an even smaller margin — which is why it is practised. After touchdown the reversers are stowed and the decision is made quickly.
Missed approach
Every instrument approach has a published missed approach procedure — exactly what to fly if you do not land: where to climb, which way to turn and where to go (often into a holding pattern or back for another attempt). It begins at the missed approach point (MAP) or on reaching the minimum without visual contact. The crew knows this procedure from the chart and the briefing, so during a go-around they simply “execute" it (see types of approach, IFR).
Deciding in time — the “go-around mindset"
Paradoxically, the problem is often making the decision. Pilots sometimes succumb to continuation bias (“we're almost there, I'll press on") and continue an unstable approach instead of going around — this has been behind a number of landing accidents. That is why a go-around mindset is taught: go into the approach treating the go-around as the default option, and “confirm" the landing only when the criteria are met. The stabilised approach rule applies (on centreline, glide path, speed and configuration by ~1,000 ft IMC / 500 ft VMC) — otherwise go around, without hesitation.
The somatogravic illusion and risks
A go-around has its own dangers. With sharp acceleration (applying full thrust), the somatogravic illusion arises: the acceleration feels to the senses like pitching up, even though the aircraft is climbing normally. The pilot may then have the false sensation that the nose is too high and push it down — which at night or in IMC has led to impacts with the ground. Defence: trust the instruments (attitude indicator), not the sensation. A low-altitude go-around at night is therefore a critically demanding manoeuvre, and several accidents (e.g. over the sea at night) have resulted from it (see Air accidents).
Single-engine go-around
A demanding variant is a go-around with a failed engine (after a failure during the approach). The thrust is asymmetric and the aircraft tries to yaw and roll, so the pilot must actively compensate with rudder and bank and watch the minimum control speed. Climb performance is limited. This scenario is a standard part of simulator training, because in reality there is no room to practise it.
ATC and communication
A go-around is reported to ATC (“going around"). ATC then sequences the aircraft — either along the published missed approach procedure, or with vectors for another attempt or to the alternate. At a busy airport a go-around is routine and ATC expects it; the important thing is to report it clearly and in time, so that the path is cleared and traffic separated.
Go-around in a small aircraft
Even a VFR pilot in a small aircraft (e.g. a Cessna 172) must be able to go around — say after a bad landing, an animal on the runway or traffic in the circuit. The procedure is simpler, but the logic is the same: full throttle, hold the nose for the climb, retract the flaps gradually (not all at once — lift would be lost), with a positive climb the gear if retractable, and return to the circuit. Go-arounds are practised from the very start of training, because “forcing" a botched landing is a common cause of accidents in light aviation too.
Practical steps — X-Plane / DCS
Practise go-arounds from minima and from an unstabilised approach (the Zibo/ToLiss have a TOGA button and SRS/FD guidance). In DCS naval operations, a “bolter" (missing the wire) is in effect a go-around — full thrust immediately after touching the deck.
Common mistakes
- Hesitation — the decision at the DA/DH must be immediate.
- Forgetting thrust/attitude — thrust and pitch first, then configuration.
- Not following the MAP — after climbing, fly the published procedure, not “blind".
FAQ
Is a go-around a sign of a mistake? No — it shows good judgement; it is always safer than a risky landing.
Who can call it? The pilot at any time, and also ATC.
Safety and limitations
- A go-around is always an option — until touchdown (and on a “touch and go").
- A stabilised approach is a prerequisite; otherwise go around.
Related links
- ILS approach · Types of approach · Autopilot
- Glossary — go-around, TOGA, MAP, DA/DH, MDA
Sources (verified 06/2026): ICAO Doc 8168 PANS-OPS, flight manuals (FCOM/POH); naval procedures per Eagle Dynamics. An educational summary; for a real flight, use current official documents.