Glass cockpit vs steam gauges

1 contributors Last edited: Anonym Updated: 14. 6. 2026 Revision history

Glass cockpit vs. steam gauges — analogue vs. digital

Flight instrumentation follows two philosophies: “steam gauges" (analogue instruments, where each quantity has its own dial) and the “glass cockpit" (digital displays that integrate the data). Modern aircraft are moving to glass, but analogue instruments remain in thousands of GA aircraft and understanding them is fundamental — not only for historical reasons, but also for partial panel flying (flying with some instruments out of service).

📷 Image placeholder: a steam-gauge panel (C172) compared with a glass cockpit (G1000)
We will add a real cockpit photo.

Steam gauges — the classic “six"

The classic arrangement (“six-pack", “sacred six", in the basic T layout):

“Six-pack" / basic T (analogue instruments) ASIairspeed indicator (pitot) AIattitude indicator (gyro) ALTaltimeter (static) TCturn coordinator (gyro) HI / DGdirectional gyro VSIvertical speed (static) “Basic T" = ASI · AI · ALT · HI form the letter T in the middle of the panel.
InstrumentWhat it measuresSystem
ASI — airspeed indicatorairspeed (coloured arcs, VNE)pitot-static
AI — attitude indicatorpitch and bankgyroscope
ALT — altimeteraltitude above sea level (Kollsman window, QNH)static (aneroid)
TC — turn coordinatorrate of turn + ball (slip/skid)gyroscope
HI/DG — directional gyroheadinggyroscope
VSI — vertical speed indicatorvertical speedstatic

They are divided into gyroscopic (AI, HI, TC — rigidity in space) and pitot-static (ASI, ALT, VSI — pressure from the pitot tube and static port; only the ASI uses the pitot, all three use static).

Advantages: simplicity, (partial) independence, intuitiveness, low cost; some work even without electrical power. Disadvantages: gyro precession, limited accuracy, many instruments, no data integration.

History of the transition

The first “glass" cockpits appeared in airliners in the early 1980s — the Boeing 757/767 (1982) and the Airbus A310 were among the pioneers with CRT displays. The Airbus A320 (1988) brought a fully glass fly-by-wire cockpit with a sidestick and ECAM. Glass only reached general aviation around 2003 (Avidyne Entegra, Garmin G1000), when LCDs and compact AHRS/ADC units became cheaper. Today glass is standard from trainers to airliners — but even the most modern glass cockpit has backup analogue or ISIS instruments just in case, because electronics can fail.

Glass cockpit — digital displays

Instead of dials there are electronic displays (EFIS). The main elements:

  • PFD (Primary Flight Display) — attitude, speed, altitude, heading, vertical speed, FMA — the primary flight information on one display.
  • ND (Navigation Display) — a map with the route, waypoints, terrain, weather and TCAS.
  • MFD (Multi-Function Display) — multi-purpose (maps, systems, performance), switchable by page.
  • EICAS (Boeing) / ECAM (Airbus) — engine and system monitoring + alerts and checklists.

Sensors behind the displays

The displays themselves measure nothing — the data come from computers:

  • ADC (Air Data Computer) — air data (speed, altitude, temperature) from the pitot-static system.
  • IRU/IRS — inertial reference (position, heading, attitude) from laser gyroscopes.
  • ADIRU — combines the ADC + IRU into one unit (airliners).
  • AHRS — a replacement for gyroscopes in GA (attitude/heading); together with an ADC it forms an ADAHRS.

Backups and advanced functions

  • ISIS (Integrated Standby Instrument System) — a backup electronic instrument with three basic items: speed, altitude, attitude; it works if the main displays fail.
  • SVS (Synthetic Vision) — a 3D view of terrain and obstacles on the PFD; it greatly improves awareness in reduced visibility.
  • Integration of terrain (TAWS), traffic (TCAS) and weather directly into the map.

Manufacturers

  • Garmin — G1000 (since 2003, the GA standard), G3000/G5000 (touchscreen, turbines/VLJs), with SVS.
  • Collins — Pro Line 21, Pro Line Fusion (business/regional).
  • Honeywell — Primus Epic; Avidyne Entegra (GA).
  • Boeing / Airbus — their own EFIS suites in airliners.

Advantages vs. risks of the glass cockpit

Advantages: integration (everything on one display), synthetic vision, a map with terrain/traffic/weather, fault detection, customisation, less panel space. Risks:

  • Dependence on electrical power — hence ISIS and backup batteries.
  • Automation dependency (“children of the magenta line") — the pilot loses manual skills and awareness and blindly follows the display.
  • Complexity — more modes and pages, a risk of mode confusion.

Partial panel — why steam is still taught

When an instrument fails, the pilot must be able to fly with the remaining ones. With steam gauges this means, for example, a vacuum system failure (AI/HI) → flying by the ASI, ALT, TC, VSI and compass. With glass, the backup is the ISIS and the procedure for the type. That is why training is also done on partial panel.

GA vs. airliner

In GA, glass is typically a G1000 (PFD + MFD) in a Cessna 172 G1000 or DA40. In airliners glass is standard (PFD + ND + EICAS/ECAM + FMS), with full automation and autoland. A steam-gauge scan is still a basic skill for partial panel, even for airline pilots.

Practical steps — simulators

  • MSFS/X-Plane: start with steam (Cessna 172 classic) — you will understand the principles of the instruments — then move to the G1000 (DA40/C172 G1000). Practise partial panel (fail the AI).
  • Airliners (PMDG/Fenix/Zibo/ToLiss): learn the PFD/ND and the EICAS/ECAM alerts.
  • DCS: combat aircraft combine a HUD + MFDs (digital), but also have backup analogue instruments in case of damage — learn to switch to them.

Common mistakes

  • Blindly following the display (automation dependency) — check the overall picture.
  • Not knowing the backups (ISIS / partial panel) when something fails.
  • Mode confusion on a complex glass system — read the FMA/modes.
  • Ignoring gyro precession on steam gauges (reset the DG to the compass).

FAQ

Why “steam gauges" when they don't run on steam? A nickname for analogue dials — to distinguish them from digital displays.

What is “children of the magenta"? A well-known lecture about excessive reliance on automation (magenta = the colour of the route on the ND).

What if the displays fail? The ISIS (speed, altitude, attitude) and the type's procedures take over.

Should I learn steam if I fly glass? Yes — the principles and partial panel are fundamental to safety.

Safety and limitations

  • Backups (ISIS, battery, partial panel) are essential — glass depends on electrical power.
  • Scan and overall awareness, not fixation on one value.
  • Keep up manual skills even in the age of automation.

What the PFD (Primary Flight Display) shows

The PFD is the main flight display — the digital successor of the “six-pack", which concentrates all flight control information in one place in front of the pilot. On it you will find:

  • The attitude indicator in the centre (aircraft attitude, bank, pitch) — the largest and most important element.
  • The speed tape (left) with coloured limit markings and a “trend" arrow showing where the speed is heading.
  • The altitude tape (right) with the pressure setting (QNH/STD) and the vertical speed indicator next to it.
  • The heading scale (bottom) and bugs for the selected values (heading, altitude, speed).
  • The FMA (top) — a strip that shows what the autopilot and autothrottle are currently doing (see Autopilot).
  • The Flight Director command bars and the ILS deviations (LOC/G/S).

The point is for the pilot to get the complete picture at a glance instead of having to “scan" six separate dials.

PFD — what is where CLB LNAV VNAV FMA (autopilot modes) attitude indicator 250 speed 10000 altitude 360 heading
The PFD brings together everything needed for flying on one display: the attitude indicator, speed and altitude tapes, heading and, at the top, the FMA (what the autopilot is doing).

The navigation display (ND) and its modes

Next to the PFD there is usually the ND (Navigation Display) — a map of the situation around the aircraft. It has several modes: MAP (a moving map with the FMS route), PLAN (a static view of the route for checking), ARC (a sector ahead of the aircraft) and VOR/ILS (the classic rose for approaches). Further information can be layered onto the map: weather radar (thunderstorms), terrain (from TAWS), traffic from TCAS (see TCAS) and navigation points. The ND is thus the centre of situational awareness — the pilot sees where they are flying, what is ahead and where the danger is, instead of building it up in their head from numbers.

EICAS and ECAM — system monitoring

The state of the engines and systems is monitored by dedicated displays: Boeing calls them EICAS (Engine Indicating and Crew Alerting System), Airbus ECAM (Electronic Centralized Aircraft Monitor). They replaced dozens of needle gauges and warning lights and added intelligence as well: when a fault occurs they display an alert, rank it by priority and offer an electronic checklist of the steps the crew should take. ECAM/EICAS thus not only display data but actively guide the handling of non-normal situations — something that used to rely only on memory and paper manuals. Together with automation, this made it possible to reduce the crew to two pilots (the flight engineer was no longer needed).

Synthetic and enhanced vision (SVS/EVS) and the HUD

Modern glass cockpits add “vision through darkness and fog":

  • SVS (Synthetic Vision System) — draws a 3D image of the landscape on the PFD from a terrain database, as the pilot would see it in daylight; it helps with terrain awareness at night and in cloud.
  • EVS/EFVS (Enhanced (Flight) Vision System) — an infrared/sensor camera shows a real image of the outside (runway lights, terrain) even in reduced visibility; it can allow lower approach minima.
  • HUD (Head-Up Display) — a transparent display projects key data and command bars into the pilot's view, so they do not have to look down at the instruments. Common in both airliners and fighters.

These technologies improve safety especially at night, in bad weather and in rugged terrain — and in the sim they show nicely where cockpit development is heading.

Display architecture, reversion and data buses

The strength of the glass cockpit also lies in its flexibility. The displays (DUs, Display Units) are often interchangeable and connected by data buses, so when one display fails its content is automatically moved to another (so-called reversion) — the pilot is not left “blind". Data come from several independent sources (sensors: ADIRU/AHRS, ADC) and are compared with each other; if they disagree, the system warns. This redundancy makes the glass cockpit, despite the apparent “fragility" of screens, a very reliable and robust system — supplemented by independent backups (ISIS).

Modern trend: touch and large screens

The newest cockpits (e.g. the Boeing 777X, business jets with the Garmin G3000 or Pro Line Fusion) are moving to large touchscreens that combine the PFD, ND and system and FMS controls on a single surface. Buttons are disappearing, configurability is growing and the crew can customise the layout. The trend is towards integrated “glass" surfaces similar to a tablet — with an emphasis on clarity and reduced workload. That is another reason to understand the principles: technology changes, but the logic of “what the display shows and why" remains.

MFD — multi-function display

Besides the PFD and ND, aircraft usually have an MFD (Multi-Function Display) — a universal screen on which the crew can call up, as needed, the map, system pages, flight plan, weather radar, checklists or fuel status. One display thus does the job of many separate instruments, and the crew displays exactly what they need in a given phase of flight. In small aircraft (e.g. the Garmin G1000), the PFD + MFD pair forms the whole “glass" cockpit; in airliners the MFD is part of a larger display arrangement.

Moving from the six-pack to glass

For a pilot, moving from analogue to glass is not just cosmetic — the way of working changes. Instead of “scanning" six dials, the pilot reads an integrated picture, but in exchange must learn to operate the systems (FMS, autopilot modes, display pages) and above all understand what the automation is doing. Paradoxically, the glass cockpit therefore places different, not smaller, demands on the pilot: there is less manual interpretation of instruments, but more system management and a risk of “mode confusion". That is why, even in the era of glass cockpits, reading classic instruments and hand flying are still practised (see the classic six-pack).

When a display fails — what to do

A screen failure sounds frightening, but the glass cockpit is designed for it. The content of the faulty display is usually moved to another one (reversion), so the pilot does not lose key information. If several displays or data sources fail, independent backups take over — the integrated standby instrument ISIS (attitude, speed, altitude) with its own power supply. The crew then flies on the backups and handles the failure according to the procedures (with the help of ECAM/EICAS). The key is not to panic, switch to the backups and “fly the aircraft" — which is why emergency modes (display failure, reversion, flying on the ISIS) are practised in the sim too; it is instructive and valuable situational awareness training.

Related links


Sources (verified 06/2026): Pilot Institute (six-pack), SKYbrary (Glass Cockpit, ADIRU, ADC), Wikipedia (ISIS, Glass cockpit), Garmin/Collins (G1000/G3000, Pro Line); components and sensors verified from multiple sources.