Autopilot — automatic flight control systems

2 contributors Last edited: Anonym Updated: 14. 6. 2026 Revision history

Autopilot — automatic flight control

The autopilot (AP) is a set of systems that automatically operate the control surfaces — and in airliners also the engine thrust — so that the aircraft holds a selected altitude, heading or speed, or flies along a programmed route. The point is not to replace the pilot but to reduce their workload and increase precision: the pilot can devote more attention to navigation, communication and decision-making. A modern autopilot can fly from shortly after takeoff all the way to a fully automatic landing (autoland).

📷 Image placeholder: a real glass cockpit with the autopilot panel (MCP/FCU)
We will add a real photo / screenshot.

How an autopilot works — the control loop

An autopilot is a feedback controller. It constantly compares the selected state (e.g. an altitude of 5,000 ft) with the actual state from the sensors and converts the difference (error) into a control surface deflection. As the aircraft approaches the target, the correction weakens — which is why the autopilot does not “overshoot" and holds the value smoothly.

The autopilot control loop Pilot inputMCP/FCU · FMS Flight Directorcomputes the error Autopilotservos Control surfaces+ thrust (A/THR) Aircraftresponse in the axis Feedback — sensors (ADIRU/AHRS): actual attitude, speed and altitude

This logic runs separately for each axis: pitch (→ altitude/speed), roll (→ heading/track) and, in larger aircraft, thrust. The inner loop stabilises the aircraft's attitude (quickly); the outer loop pursues a goal such as “hold altitude" or “fly to the waypoint" (more slowly).

Three layers of automation

Colloquially it is all called the “autopilot", but three separate systems work together, and they can also run independently:

SystemWhat it doesExample
Flight Director (FD)Only displays command bars (“follow the bars"). The pilot flies manually according to them; the AP does not have to be engaged.Bars on the attitude indicator
Autopilot (AP)Physically moves the control surfaces and does what the FD shows.CMD / AP1+AP2
Auto-throttle / Auto-thrust (A/THR)Controls engine thrust — holds the speed or a set thrust.Boeing A/T, Airbus A/THR

Lateral modes — where the aircraft is heading

  • HDG / TRK — holds the selected heading / track.
  • LNAV / NAV / managed — follows the route from the FMS (waypoints, SID/STAR).
  • LOC — captures and tracks the ILS localizer.
  • ROLL / wing leveler — basic roll attitude hold on simpler APs.

Vertical modes — how the aircraft climbs and descends

  • ALT HOLD — holds the current altitude.
  • V/S — holds a selected vertical speed (e.g. −1,500 ft/min).
  • FLCH / OP CLB / OP DES — climb/descent to a selected altitude; the speed is held by the elevator.
  • VNAV / managed — follows the vertical profile from the FMS, including altitude and speed restrictions.
  • G/S — captures and tracks the ILS glideslope.

Thrust and speed: two philosophies

A principle that confuses beginners — speed can be held either by thrust or by pitch:

  • Speed-on-thrust — in level flight and on a path descent the autothrottle holds the speed, and the elevator holds the altitude/descent path.
  • Speed-on-pitch — in a climb/open descent (OP CLB/DES, FLCH) the thrust is fixed and the speed is held by pitch (the elevator).

FMA — where the pilot reads what the autopilot is doing

The Flight Mode Annunciator (the strip above the attitude indicator) is the most important display when working with automation. Each mode is in one of two states:

FMA — mode strip (Boeing style) THRUST (A/THR)VERTICALLATERAL SPDVNAV PTHLNAV G/S LOC ■ large green = ACTIVE (flying the aircraft now) ▭ smaller, boxed = ARMED (waiting for a condition, e.g. beam capture)

The golden rule of automation: always know what is on the FMA. Most “mysteries" like “why is it climbing?" are just an unread FMA or an overlooked transition from an armed to an active mode.

Approach and automatic landing (autoland)

On an ILS approach, APPR (LOC + G/S) is armed first. Once both beams are captured, the autopilot brings the aircraft down to the runway. For landing in very low visibility there is autoland:

CategoryDecision HeightRVR
CAT I200 ft550 m
CAT II100 ft300 m
CAT IIIb~15 ft75 m (autoland)

Autoland requires redundancy: a fail-passive system disconnects safely in the event of a failure and the pilot takes over; a fail-operational system (dual/triple AFCS) completes the landing even if one channel fails — which is why AP1+AP2 are both lit for CAT III.

Boeing vs. Airbus — two control philosophies

BoeingAirbus
Control panelMCP (Mode Control Panel)FCU (Flight Control Unit)
LogicRather “selected" (the pilot selects values)“Managed" vs “selected" — pull/push the knob
ThrustAuto-throttle (the levers physically move)Auto-thrust (the levers stay in a detent)

Practical steps — X-Plane

📷 Image placeholder: the autopilot panel in X-Plane (e.g. the Zibo 737 MCP or the G1000 GFC 700)
We will add a real photo / screenshot.

Cessna 172 G1000 (default, GFC 700 autopilot) — a coupled ILS step by step:

  1. In stable flight press AP (engages the autopilot) and HDG, and steer towards the runway centreline.
  2. Tune the ILS frequency on NAV1, verify the Morse identification and set the inbound course.
  3. Enter the target altitude in ALT; handle the descent with VS or FLC.
  4. Below the glideslope and on the localizer, press APR — the autopilot arms and then captures the LOC and G/S in turn.
  5. At the decision altitude, disconnect the AP and land manually (the C172 has no autoland).

Zibo 737-800 (free mod): on the MCP engage CMD A, set the speed window, and use HDG SEL, LNAV, VNAV, LVL CHG, V/S, ALT HLD, and on the ILS APP (captures LOC+G/S); arm the autothrottle with A/T ARM. The Zibo also supports CAT III autoland (AP1+AP2).

ToLiss A319/A320/A321: on the FCU, pull a knob for “selected" mode and push it for “managed"; the SPD/HDG/ALT/V/S knobs, the AP1/AP2, A/THR, LOC and APPR buttons (CAT III autoland). A dot next to a value on the FCU = managed mode from the FMGS.

Deeper study modules: the FlightFactor 757/767, IXEG 737 Classic (classic MCP).

Practical steps — DCS World

A military autopilot works differently — instead of “fly the route" it offers stabilisation and hold modes.

📷 Image placeholder: the autopilot panel in DCS (A-10C II LAAP or the F/A-18C A/P page)
We will add a real photo / screenshot.

A-10C II (LAAP — Low Altitude Autopilot): three modes selected by a switch, engaged with a toggle; requires the EAC to be on (and the EGI/INS aligned):

  • ALT/HDG — holds barometric altitude and heading,
  • ALT — holds altitude only (you turn freely),
  • PATH — holds the current ground track and altitude.

F/A-18C Hornet: press A/P and then at least one mode (two presses are needed):

  • ATTH — holds pitch and bank (attitude hold),
  • HSEL — holds the selected heading (set on the HSI),
  • BALT — barometric altitude (range 0–70,000 ft),
  • RALT — radar altitude (range 0–5,000 ft); CPL (coupled to a waypoint) is also available.

F-16C Viper: the autopilot panel has two switches that can be combined:

  • PITCH: ALT HOLD (holds altitude) or ATT HOLD (holds pitch),
  • ROLL: HDG SEL (to the heading bug on the HSI), STRG SEL (to the steerpoint from the DED) or ATT HOLD (holds bank).

Ka-50 (and other helicopters): a four-channel autopilot — Pitch, Bank, Heading and Altitude hold buttons on the right panel. Pitch/Bank are usually always on (dampers / hold), the heading channel tracks direction, and the altitude channel holds barometric altitude or the hover. They are complemented by the Flight Director and the trimmer. The Mi-8/Mi-24 have similar channel stabilisation.

Safety and limitations

  • The autopilot has no judgement — it does exactly what it is told and does not assess whether it makes sense. Monitoring is always the pilot's job.
  • Trim before engaging — an out-of-trim aircraft will cause a sudden correction (“jump") when the AP is engaged.
  • Know the quick disconnect — the AP disconnect button on the stick/yoke and the A/THR disconnect. Never “fight" the autopilot with force.
  • Minimum heights — after takeoff the AP may only be engaged above a certain height, and (except for autoland) it must be disconnected on the approach in good time; the specific values are in the type's manual.
  • Garbage in, garbage out — the autopilot trusts its sensors; wrong data (e.g. a frozen pitot) lead to a wrong response. Cross-check the instruments.
  • Mode confusion — a mismatch between what the pilot expects and what the AP is doing is a documented factor in incidents. The cure: read the FMA.
  • DCS — a military AP is mainly for workload relief/stabilisation, not a tool for landing; in helicopters the channels damp rather than “fly for you".

FAQ

Does the autopilot hold the speed? Not by itself — the speed is held by the autothrottle/auto-thrust or (in a climb) by the elevator. In small aircraft without A/THR you control the throttle manually even with the AP engaged.

Why did the aircraft “jump" when I engaged the AP? Most likely it was not trimmed. Trim before engaging the AP.

What if TCAS issues an RA with the AP engaged? Disconnect the autopilot and fly the manoeuvre manually according to the RA (some modern types can perform the avoidance automatically — follow the procedures for the particular aircraft).

Can the autopilot take off? No. Autoland exists, but “auto-takeoff" does not on ordinary airliners — takeoff is always manual.

Does the autopilot turn by itself? Yes, in route-tracking mode (LNAV/NAV) it turns towards the waypoints automatically; in HDG after a new heading is set.

Channels, servos and redundancy

The autopilot physically acts on the control surfaces via servo motors (servos) — separately for roll (ailerons/spoilers), pitch (elevator) and, in larger aircraft, yaw (rudder). Each controlled axis has its own “channel". A small aircraft usually has a simple single-axis autopilot (wing leveller only) or a two-axis one; airliners have full three-axis systems. One autopilot is enough for normal flight, but automatic landing (CAT II/III) requires redundancy: several autopilots are engaged at the same time so that a failure of one channel does not interrupt the approach. Airbus shows this with the annunciation LAND 2 / LAND 3 (how many independent systems are monitoring the landing), Boeing similarly. A distinction is made between fail-passive (a failure safely disconnects the system) and fail-operational (it continues to function even after a failure) — and fail-operational is the prerequisite for the lowest minima (see ILS, CAT III).

CMD and CWS — engagement modes (Boeing)

Boeing distinguishes two ways of engaging the autopilot. CMD (Command) is full command — the autopilot flies according to the modes selected on the panel (MCP) and from the FMC. CWS (Control Wheel Steering) is a hybrid: the autopilot holds the attitude (bank and pitch) that the pilot sets by moving the control wheel, and keeps holding it after release. CWS thus combines the manual “feel" of the aircraft with automatic attitude hold. In Airbus aircraft, similar smoothness is provided by the fly-by-wire itself with envelope protection (see A320), so classic CWS is not needed.

Flight Director (FD) — command bars

The Flight Director is an “advisor" that displays command bars (a cross or a “V") on the PFD/ADI, showing where the pilot should steer to satisfy the selected modes. The key point is that the FD and the autopilot are computed by the same guidance system — the only difference is who moves the controls. With the autopilot engaged, the automation flies according to the FD; with the autopilot off, the pilot can manually “follow the bars" and fly exactly the same plan. The FD is therefore the bridge between fully manual and fully automatic flight, and one of the first things a sim pilot learns to read in an airliner.

Flight Director — command bars The pilot (or autopilot) steers the aircraft symbol into the command “V".
The FD bars show where to steer for the aircraft to satisfy the selected modes. The same guidance system also drives the autopilot — the only difference is who is at the controls.

History of the autopilot

The principle of the autopilot is surprisingly old. As early as 1914, the Sperrys (Elmer and Lawrence Sperry) demonstrated a gyroscopic stabiliser that kept an aircraft in straight and level flight — Lawrence Sperry famously demonstrated it by raising his hands from the controls in flight while his mechanic walked out along the wing. Over the decades, gyroscopic stabilisation evolved into an autopilot capable of holding heading and altitude, later of guiding by radio beacons, and finally (with the arrival of computers and the FMS in the 1980s) of controlling the whole flight profile and landing automatically. The development of the autopilot thus mirrors in miniature the development of aviation as a whole — from mechanics and gyroscopes to digital control.

Automation and human factors

Increasing automation brought a new category of error — misunderstanding what the automation is currently doing. A classic lesson is the Asiana 214 accident (Boeing 777, San Francisco 2013): the crew relied on the autothrottle to maintain speed, but in the mode it was in, it was not doing so; the aircraft slowed, sank below the glide path and touched down short of the runway. The NTSB cited improper use of automation and inadequate speed monitoring as factors. Hence the phrase “children of the magenta line" — a warning against blindly following the FMS's magenta line without understanding and checking. The lesson for pilots and sim pilots alike: automation is a powerful tool, but the pilot must know which mode the aircraft is in, what the automation is doing, and be able to switch it off at any time and fly by hand (see Air accidents, CRM).

Related links


Sources (verified 06/2026): manufacturer documentation (Boeing FCOM, Airbus FCOM/FCTM), flight manuals (POH/AFM), ICAO Annex 6; sim-specific details per the documentation of Eagle Dynamics (DCS A-10C II Flight Manual, F/A-18C, F-16C, Ka-50) and the X-Plane module developers. An educational summary; for a real flight, use current official documents.